KALTEC

BlogApplication notes

Why is my bearing running hot?

Type
Application notes
Published
20 November 2026
Prepared by
Technical team
Product group
Greases

Adding more grease is the usual response to a hot bearing, but surplus grease churns and makes heat itself, so it can push the temperature higher. What actually heats a bearing can be too much grease, too little grease, the wrong viscosity, grease spoiled by oxidation, dirt, water or mixing, or misalignment and overload, and one cause often brings on another.

On a routine round, a motor or fan bearing housing is sometimes too hot to keep a hand on, and the infrared thermometer reads clearly higher than last month's log. The noise still sounds fine and the machine still runs, so it is easy to let it pass, yet a rise in temperature is a sign that something inside the bearing is wrong.

A hot bearing threatens cost and safety at once. As temperature rises, the grease ages faster and needs replacing sooner, and the oil film thins so wear speeds up. At the end of that road lie an unplanned bearing change and a stopped machine. Too much heat even leaves damage where the metal has deformed from heat (Timken Company, 2014). Heat is both a result and a cause: whatever starts it, the film and the grease weaken together, and that in turn raises friction and heat.

A rolling bearing runs on a very thin oil film between the rolling elements, the balls or rollers, and the raceways, the running tracks of the rings. As the oil passes through the contact it is put under very high pressure and briefly behaves almost like a solid, a state called elastohydrodynamic lubrication (Brown, 2015). Grease is a reservoir that holds this oil, the base oil, in a sponge-like structure called the thickener and releases it little by little (Lugt, 2009; Timken Company, 2014). When temperature rises, the base oil's viscosity falls and the film thins (Brown, 2015), and grease life shortens too. A rule of thumb says that within a certain range grease life roughly halves with every 15 °C rise (Lugt, 2013), and another source gives a smaller step for the breakdown rate to double (Timken Company, 2014), so the direction matters more than the exact figure.

In such cases the technical team sets up the five hypotheses below and rules them out one by one. The start is always the same: find out when the bearing was last greased and how much went in, then measure the surface temperature at the same spot and the same load and compare it with past records. That one comparison screens several hypotheses at once.

Hypothesis 1: over-greased

If the bearing got hot right after greasing, suspect the amount first, because the records answer it straight away. It shows up with the habit of pumping the grease gun until grease appears rather than delivering a set amount, with maintenance that logs only the number of strokes, and on bearings whose relief port is missing or blocked so surplus grease has no way out. Think of a routine greasing day. A technician gives each fan bearing a generous dose as usual and moves on, and on the afternoon round those very bearings have hot housings and grease squeezed out at the seals.

The heat right after greasing comes from the grease finding its place. Fresh grease first sits between the rolling elements, and as the bearing turns they push it into the spaces they do not sweep. This is called the churning phase, and while it lasts friction losses and temperature are high (Lugt, 2013). The displaced grease settles on the seals, ring shoulders or cage as a reservoir, and the bearing moves on to a phase in which that reservoir releases oil slowly and the temperature falls (Lugt, 2009; Lugt, 2013). Without free space to push it into, things go differently. Too much grease keeps the bearing in the churning phase, with high friction losses and high temperature (Lugt, 2013). The high temperature speeds grease breakdown, and the surplus forces its way past the seals; over time the leaked grease darkens and smells burnt (Timken Company, 2014).

Checking starts by laying two records side by side. Overlay the greasing schedule on the temperature log and see whether temperature jumps after each greasing. Look at the colour of grease pushed out at the seals or relief port as well. A small leak of clean grease at start-up is common even in a correctly lubricated bearing (Timken Company, 2014), so colour and smell are the clue, not the amount. Measure temperature with a contact thermometer or an infrared camera at the same spot and the same load. Thermography needs correction for surface reflection and emissivity before readings can be compared (ISO, 2008).

A temperature that rose after greasing and settles back to normal over time may simply have been the churning phase. If it does not come down, open the relief port to let the surplus out, and from then on follow the equipment maker's amount and purging practice (Timken Company, 2014). Measure how much one stroke of the grease gun delivers, and record the amount by weight or volume rather than by strokes. On bearings without a relief port the surplus has nowhere to go, so keep to the amount especially strictly.

Hypothesis 2: under-greased

When temperature has crept up over weeks or months rather than right after greasing, look the other way. It shows up on bearings in awkward places where intervals are often missed, on machines whose maintenance schedule has slipped, on sealed bearings with small reservoirs, and in hot surroundings where grease is used up faster. A conveyor bearing mounted high at the back of a machine is a good example. It needs a ladder to reach, so a greasing or two got skipped, and one day its temperature starts rising and a grinding note creeps into the sound.

A grease-lubricated bearing does not run bathed in oil. Once churning is over, the raceway carries only a thin oil layer, refilled by oil bleeding from the reservoirs as fast as it is lost to side flow and oxidation (Lugt, 2013). When losses outrun the refill, the film thins; this is called starvation (Cann, 1999; Lugt, 2013). Sealed bearings, with their small reservoirs, are especially prone to it (Lugt, 2013). Once the thinning film lets metal touch metal, friction rises, heat follows and metal wears, and grease from an underfilled bearing comes out laced with metal debris (Timken Company, 2014). If relubrication never comes, the film breaks down badly, a point called the end of grease life, and bearing damage follows (Lugt, 2013).

Sound and grease tell this hypothesis best. A sudden rise in noise together with temperature signals wear in progress (Timken Company, 2014), and purged grease that looks dry or shows metal debris makes this hypothesis the strong one. Measure vibration at the same points at fixed intervals and compare it with the usual baseline by the method the standard sets out (ISO, 2016). Check the greasing log for missed intervals, and whether a logged greasing was at a spot that is hard to reach in practice.

Once starvation is confirmed, make up the missed greasing first. Add the equipment maker's amount and watch whether temperature and noise come down. In hot surroundings grease life is shorter (Lugt, 2013), so set a shorter interval. For spots that get missed because they are hard to reach, consider running a grease line out to an accessible point or fitting an automatic lubricator. If metal debris shows or the noise does not drop, the surfaces may already be damaged, so do not stop at refilling; plan a bearing inspection.

Hypothesis 3: wrong viscosity

Even with the right amount and interval, a bearing runs hot if the grease itself does not suit the position. This often shows after a speed increase or process change, after a change of season alters the running temperature, or after a switch to a different grease. Take a plant that moves to a single grease everywhere to simplify stores. A few weeks later the fast fan bearings run hotter than before, while the slow, heavily loaded conveyor roller bearings start to show wear.

Base-oil viscosity decides whether the trouble is heat or wear. Film thickness is set mainly by base-oil viscosity, and higher viscosity gives a thicker film (Brown, 2015). The bearing life standard adjusts rated life by the viscosity ratio, kappa, which is the actual viscosity at operating temperature divided by the reference viscosity the bearing needs (ISO, 2007). A ratio between 2 and 4 keeps the surfaces fully apart, 0.4 to 2 is mixed lubrication with some contact, and below 0.4 is boundary lubrication (Brown, 2015). Too low a viscosity thins the film and raises temperature, leading to micro-spalling, a fine peeling of the raceway surface, and wear (Timken Company, 2014). Too high makes heat as well. Above a ratio of 4 the gain tails off and the oil's viscous drag makes heat that lowers the operating viscosity (Brown, 2015), and a grease with too high a viscosity can make the rolling elements skid instead of roll, causing grease breakdown and wear (Timken Company, 2014).

Two numbers come first. Compare the base-oil viscosity of the grease in use, and its consistency grade, which says how stiff it is, with the equipment maker's recommendation. Consistency is graded by the cone penetration test, which measures how far a cone sinks into the grease (ASTM International, 2021). Then see whether the overheating lines up with a change in speed, running temperature or grease type. Required viscosity depends on bearing size, speed and running temperature (Brown, 2015; ISO, 2007), so a change in any one of them can turn a suitable grease into an unsuitable one.

Choosing the grease again starts with a calculation. Work out the required viscosity from the bearing's mean diameter, speed and running temperature, and pick a base-oil viscosity that gives a ratio of roughly 2 to 4 (Brown, 2015; ISO, 2007). For a fast bearing running hot, check whether the viscosity is too high; for a slow, heavily loaded one running hot with wear, check whether it is too low. Where heavy load makes the right ratio hard to reach, consider a lubricant with extreme-pressure additives, which form a protective layer on the metal under severe contact (Brown, 2015). Grouping positions with similar duty and choosing for each group is safer than one grease for the whole plant.

Hypothesis 4: spoiled grease

Grease put in at the right amount and viscosity can still spoil in service. It shows up on bearings topped up for a long time without a full change, in hot positions, on machines that are washed down often or exposed to rain and dust, and on sites where different maintenance crews carry different grease guns. Picture a pump bearing on a food line that is hosed down often. Since its seals wore, the grease pushed out at the relief port has turned milky and runny, unlike new grease, and the housing temperature has been edging up ever since.

Grease spoils by several routes. The first is oxidation. Grease contains antioxidants that slow oxidation; once they are used up, at a point called the induction time, oxidation takes hold and the grease loses base oil and lubricity. In real bearing tests oxidation dominated grease life, and the induction time depended on running conditions and oxygen concentration (Lugt et al., 2023). The higher the running temperature, the more oxidation stability decides grease life (Schneidhofer et al., 2025). Over time the sponge also loses its ability to hold and release oil, leaving worn-out grease whose thickener and additives have decomposed and whose base oil is breaking down (Timken Company, 2014).

The second route is mixing. Two incompatible greases mixed together either soften and leak out, or turn lumpy, discoloured and hard (Timken Company, 2014). The third is contamination. Water brings rust and corrosion marks on the raceways, and dirt and sand from outside or wear particles from inside travel through the bearing in the grease and dent the raceways, bringing damage sooner (Timken Company, 2014). Whatever the route, oil stops reaching the raceway properly, and heat then builds by the same starvation path as in hypothesis 2 (Lugt, 2013).

Comparison by eye and nose is the first check. Set purged grease beside new grease and compare colour, smell and stiffness. Dark and hard, or far too runny, points to degradation; lumpy and discoloured points to mixing (Timken Company, 2014). Whether water got in can be seen with a simple test. Put a grease sample on aluminium foil and warm it from below with a flame: if it melts and smokes lightly there is little or no water, and if it crackles, sizzles or pops it holds a fair amount (Timken Company, 2014). Also check whether the grease type changed recently, whether crews use different greases, and whether the seals are worn.

Once the grease is judged spoiled, the answer is replacement, not top-up. Open the relief port and purge the old grease out with new, or if the condition is bad, clean the bearing and refill. When changing to a different grease, confirm from supplier data that the thickeners and base oils are compatible, and label each grease gun and fitting with the grease name so they are not mixed. If water and dirt were to blame, replace the seals and keep washdown spray off the bearings. In hot positions, consider a grease with higher oxidation stability together with a shorter interval (Lugt, 2013; Schneidhofer et al., 2025).

Hypothesis 5: uneven or heavy load

When the lubrication has all been put right and the temperature still will not come down, suspect the forces the bearing carries. This tends to show right after work that disturbs the shaft, such as a motor change, a coupling change or foundation work, on machines whose shaft position shifts with thermal growth in service, and on drives where a belt has just been fitted and re-tensioned. Sometimes, from the week after a motor is replaced, only the coupling-side bearing runs hotter than the far side. Fresh grease does not change the gap, nor does a different grease, and the coupling itself feels warm to the hand.

Uneven force means uneven heat. A bearing keeps contact pressure low when load is shared evenly across many rolling elements. When the shafts are out of line, load gathers on a few elements and on the edge of the raceway, and the pressure on the contact, the Hertzian stress, rises. A computer model study of a cylindrical roller bearing found that even small angular misalignment raised contact stress, and that the outer ring was the part most prone to damage (Mashiyane et al., 2022). Misalignment also makes heat at the coupling. On a small test rig, deliberately offsetting the shafts raised the coupling temperature, and the researchers reported that temperature monitoring can detect misalignment, though the rate of rise depended on machine condition and ambient temperature (Tonks & Wang, 2017). The heat produced this way also speeds up grease ageing (Lugt, 2013), so long-standing misalignment brings the degradation of hypothesis 4 in its wake.

The shape of this hypothesis appears when temperatures are compared along the shaft. Take one thermal image that holds the coupling-side bearing, the coupling and the far-side bearing, and read the temperature difference along the shaft (ISO, 2008; Tonks & Wang, 2017). Measure vibration at the same points and compare it with the baseline from before the work (ISO, 2016). Match the date the overheating began to the maintenance log and check whether it followed a motor or coupling change, foundation work or a belt change. Also confirm that belt tension, the shaft and housing fits and the actual running load are within the design.

First, realign the shafts with measuring equipment. On machines whose position shifts with thermal growth in service, align for the running position at operating temperature, not the cold position at rest. Return belt tension and fits to the design values. If the load itself exceeds the design, lubrication cannot solve it, so hand it over for a design or operating review. After realigning, purge and refill with new grease, since grease that has been running hot may already be spoiled.

Testing the hypotheses

Five hypotheses do not call for five investigations at once. Rule them out one at a time, starting with what the records answer straight away.

The first step is to make sure the temperature just measured can be trusted. Measure at the same spot and the same load, and for thermography correct for emissivity and reflection (ISO, 2008). With no past records, compare with similar bearings on the same machine. Then look at the shape of the temperature trend. Whether it jumped right after greasing, crept up over weeks, or stepped up right after maintenance decides which hypotheses to look at.

Next come the greasing log and the purged grease. If temperature rose right after greasing, put hypothesis 1, the amount, first; if an interval was missed or purged grease is dry with metal debris, put hypothesis 2 first (Lugt, 2013; Timken Company, 2014). Purged grease that is dark and hard, runny or lumpy points to spoiled grease, hypothesis 4 (Timken Company, 2014). These two checks alone, the log and the grease, screen out much of hypotheses 1, 2 and 4.

If that still does not settle it, move on to comparison. If the overheating coincides with a change in speed, running temperature or grease type, recalculate the viscosity ratio to test hypothesis 3 (Brown, 2015; ISO, 2007). Comparing with other positions on the same grease helps too: if only the fast ones run hot and only the slow ones wear, viscosity is the likely problem. If nothing changes once the lubrication is right and only one bearing runs hot, read the temperature along the shaft by thermography and measure alignment and load to test hypothesis 5 (Tonks & Wang, 2017).

Once the cause is found and fixed, the last step is to confirm it in the trend. It is done only when temperature and vibration, measured at the same points over several checks after the fix, return to the usual baseline and stay there (ISO, 2016).

One more thing to remember: the hypotheses often overlap. Heat from misalignment or overgreasing oxidises the grease faster, and oxidised grease then starves the bearing. Changing only the grease will soon bring the same result, so fix whatever started the heat first, then refill with new grease.

Limits and cautions

Normal running temperature, grease amount and interval differ by machine, so follow the equipment maker's instructions for any figures, and look at the trend of the same bearing and the gap to its neighbours rather than an absolute value. The relation between temperature and grease life given above is a rule of thumb from the sources. Plain bearings, circulating-oil systems, high-speed spindles and damage from shaft currents in motors involve other mechanisms and need a different judgement. If temperature climbs fast, noise and vibration rise together, or there is smoke or a burnt smell, stop the machine and have a bearing specialist inspect it.

Safety matters too. When measuring or greasing running machines, keep clear of rotating parts and hot surfaces, and isolate and lock out energy before alignment or teardown. A high-pressure grease gun can force grease under the skin, so never point the nozzle at the body. Never spin a bearing with compressed air, since its parts can be thrown out (Timken Company, 2014). Follow the product's safety data sheet, the SDS, for handling and protective equipment.

Sources

  1. ASTM International. (2021). ASTM D217-21, Standard test methods for cone penetration of lubricating grease. https://store.astm.org/d0217-21.html
  2. Brown, S. F. (2015, August). Selecting the right lubricant for rolling element bearings. Tribology & Lubrication Technology. Based on an STLE webinar by J. Oliver. https://www.stle.org/images/pdf/STLE_ORG/BOK/LS/Bearings/Selecting%20the%20Right%20Lubricant%20for%20Rolling%20Element%20Bearings_Aug15%20TLT.pdf
  3. Cann, P. M. (1999). Starved grease lubrication of rolling contacts. Tribology Transactions, 42(4), 867–873.
  4. International Organization for Standardization [ISO]. (2007). ISO 281:2007, Rolling bearings — Dynamic load ratings and rating life.
  5. International Organization for Standardization [ISO]. (2008). ISO 18434-1:2008, Condition monitoring and diagnostics of machines — Thermography — Part 1: General procedures. https://www.iso.org/standard/41648.html
  6. International Organization for Standardization [ISO]. (2016). ISO 20816-1:2016, Mechanical vibration — Measurement and evaluation of machine vibration — Part 1: General guidelines. https://www.iso.org/standard/63180.html
  7. Lugt, P. M. (2009). A review on grease lubrication in rolling bearings. Tribology Transactions, 52(4), 470–480. https://doi.org/10.1080/10402000802687940
  8. Lugt, P. M. (2013, June 28). Grease lubrication mechanisms in rolling bearing systems. Evolution. SKF technical magazine. https://evolution.skf.com/grease-lubrication-mechanisms-in-rolling-bearing-systems/
  9. Lugt, P. M., Holgerson, M., & Reinholdsson, F. (2023). Impact of oxidation on grease life in rolling bearings. Tribology International, 188, 108785. https://doi.org/10.1016/j.triboint.2023.108785
  10. Mashiyane, T., Dawood, B., & Tartibu, L. (2022). Numerical simulation of the effect of angular misalignment on the dynamic behaviour of bearing. MATEC Web of Conferences, 370, 09003. https://doi.org/10.1051/matecconf/202237009003
  11. Schneidhofer, C., Schandl, M., Dörr, N., & Lugt, P. M. (2025). A model describing the oxidation rate of lubricating greases. Frontiers in Mechanical Engineering. https://doi.org/10.3389/fmech.2025.1591795
  12. Timken Company. (2014). CV15, Inadequate grease lubrication in bearings. Commercial Vehicle TechTips. Retrieved November 2026. https://www.timken.com/wp-content/uploads/2017/08/CV15-Inadequate-Grease-Lubrication-In-Bearings.pdf
  13. Tonks, O., & Wang, Q. (2017). The detection of wind turbine shaft misalignment using temperature monitoring. CIRP Journal of Manufacturing Science and Technology, 17, 71–79. https://doi.org/10.1016/j.cirpj.2016.05.001

Product and site consultation

Leave your company, site and the product groups in use. Our engineer will get in touch to go through your site conditions and concerns. Materials, equipment, operating conditions and downstream steps show what should change and what can stay. If nothing needs to change, we will say so.

Contact us
After you contact us
  1. 01
    Site setup

    We confirm process conditions and needs first.

  2. 02
    Spec design

    We set the product spec and selection criteria.

  3. 03
    Comparison

    We compare matching candidates and propose.

  4. 04
    Tailored supply

    We supply on time and manage the stock.

  5. 05
    Site check

    We visit, check conditions of use and record.

  6. 06
    Use management

    We track use and change cycles to catch issues.

  7. 07
    Regular analysis

    We analyze the records and send a yearly report.