Product Application
From site registration to delivery
We analyse the customer's process environment and technical requirements in detail, review each product's performance and applicability, and propose a solution fitted to the site. This cuts the time and the trial and error that product selection takes, and contributes to a lower total cost of ownership (TCO) and better process efficiency.

- 201,329
Product recommendations to date
- 72h
Average time to a tailored solution design
- 102
Product types
Process analysis
We start with your operating conditions, equipment, past products and problems. From there we set out the performance you need and the standards the process must hold, one requirement at a time. These become the starting point for the specification.
Specification
We don't start with products. First we define the composition and properties a product needs to meet your requirements. With those set, candidates are compared on whether they fit the process rather than on familiar product names, and the reason for the final choice is clear.
Product search
Working mainly from our partner brands, we shortlist the products that meet the performance and criteria set earlier. We compare how well each one meets the criteria and which conditions it suits, and rank them. Where nothing fits, we reformulate to design a product.
Sample trial
Before full adoption, we run a sample in your actual process to confirm it performs stably. If further requirements come up during the trial, we redefine the specification and review the candidates again. Where a trial isn't needed, we skip this step and go straight to delivery.
Delivery
Once the trial confirms stability, we agree the quantities and lead times. We supply in step with your production schedule, from receipt through cleaning to the new fill, without gaps. From here, site management takes over and follows how the product performs in your process.
Four essentials of how we select products
Requirements in a work log
We sort what we hear on visits and calls into the fields of a work log. An empty field is missing information, so we confirm it before looking for products.
Products found by criteria
From the work log we draw the conditions a product must meet as recommendation criteria. Candidates are found by whether they meet them, not by product name.
Candidates compared by how they work
We set candidates side by side on active ingredients, mode of action and operating temperature range. How well each one fits your conditions, and why, is documented.
A proposal the engineer reads first
The recommended product and the reasons for it go into one proposal. Our engineer reads it first and makes the final call, and only then is it sent to you.
FAQ
What should I prepare before a consultation?
Tell us about your equipment and operating conditions, the product you use now and the problem you face. What we hear on a visit or a call goes into the fields of our work log. An empty field is missing information, so we confirm it before we look for products.
How long until I receive a proposal?
Designing a tailored solution takes 72 hours on average. Where a sample trial in your actual process is needed, we agree its schedule separately.
Can we start with just the name of the product we use now?
It helps as a starting point. But the same product performs differently under different process conditions, so we start from your requirements rather than a product name. If you share your operating conditions and problem history too, the criteria for comparing candidates become clear.
Do you only recommend partner-brand products?
We work mainly from our partner brands and look for candidates that meet the performance and criteria set from your requirements. Where no product fits, we may design one by reformulating it.
Is a sample trial always required?
Only when it is needed. We run the sample in your actual process to confirm it performs stably, and if new requirements come up during the trial we redefine the specification. Where no trial is needed, we go straight to delivery.
Can I see why a product was recommended?
We put the recommended product and the reasons for choosing it into one proposal. How well each candidate meets the criteria is documented too. Our engineer reads the proposal and makes the call before it reaches you.
How are delivery quantities and schedules set?
Once the product's stability is confirmed, we agree the quantities and lead times with you. We supply in step with your production schedule, from receipt through cleaning to the new fill, without gaps.
Do consultations or samples cost anything?
Consultations and technical reviews are free of charge. Samples are provided in the quantity the trial needs. Terms can vary with the scale of the trial and the product, so we agree them during the consultation.
Product and site consultation
Leave your company, site and the product groups in use. Our engineer will get in touch to go through your site conditions and concerns. Materials, equipment, operating conditions and downstream steps show what should change and what can stay. If nothing needs to change, we will say so.
Contact us- 01Register
You fill in your company, site and the product groups in use.
- 02Call back
Our engineer calls to go through site conditions and concerns.
- 03Site database
Materials, equipment, operating conditions, products in use and past problems are recorded per site.
- 04Proposal and quotation
You get a proposal and trial plan that compare brands by composition and working principle.
- 05Purchase, delivery, application
The confirmed product reaches your site when needed, and we check the initial condition together.
- 06Usage management
Consumption and change intervals are checked and adjusted, and the results go into the site database.
