KALTEC

Construction Equipment

From hydraulic oil filling to formwork release

The construction equipment industry builds excavators, loaders, cranes and crushers and supplies them to construction sites.

Construction Equipment
  • 92%

    Unplanned share of excavator maintenance cost

  • 82%

    Wear problems caused by particle contamination

  • 50%

    Undercarriage share of track-machine upkeep

What is the construction and heavy equipment industry?

Construction and heavy equipment builds large machines that move soil and rock, such as excavators, loaders and cranes, and supplies them to job sites. This equipment takes dust and mud directly, goes through summer and winter temperature swings, and must deliver high force all day; when it stops, the construction schedule stops too. Engines, hydraulic cylinders, reducers and crawler tracks are assembled and painted before shipping, so hydraulic and engine lubrication, heavy-duty grease, cleaning and painting and export rust protection are needed, along with release agents and rebar rust protection in on-site construction.

In heavy equipment, failures usually start with fluids. Examples include water and debris in hydraulic oil, engine oil that does not fit exhaust aftertreatment conditions, and grease washed out of pins and bushings. Whether a fluid falls within the grade set by the equipment maker, fits site environmental conditions and avoids burdening aftertreatment devices must be checked along with its performance. This is an industry where factory assembly and on-site construction run as one flow, so proposals mesh only when the conditions of both sites are understood.

  1. 01

    Material and part machining

    Engine blocks, hydraulic cylinders, gearboxes and track shoes machined by suppliers are received, inspected and stored. Rust or cutting fluid residue contaminates assembly and painting. Choose a receiving rust preventive by protection period and compatibility with supplier fluids.

  2. 02

    Hydraulic system assembly and filling

    Hydraulic cylinders and piping for travel drive and work equipment are assembled and filled with hydraulic fluid. Air mixed in during filling forms an air emulsion that unsettles response. Choose hydraulic fluid by viscosity, cleanliness grade and approved spec.

  3. 03

    Swing ring and bearing greasing

    Grease is filled into the upper structure turntable, friction bearings and pin bearings. Too little grease breaks the film on raceways and brings early fretting wear. Choose grease by extreme-pressure performance, adhesion and pumping resistance at low temperature.

  4. 04

    Crawler track drive lubrication

    Dedicated grease is applied to track links, sprockets and similar undercarriage drives. Poor water resistance washes the film out and speeds wear. Choose grease by heavy-load performance, water resistance and adhesion.

  5. 05

    Diesel engine assembly and filling

    The finished engine is installed, filled with heavy-duty diesel engine oil and warmed up before start. High-ash oil in an engine with aftertreatment builds ash in the diesel particulate filter and shortens regeneration intervals. Choose engine oil by viscosity, grade and low-ash specification.

  6. 06

    Air conditioning system charging

    Refrigeration oil and refrigerant are charged into the cab air conditioning circuit. A mismatched refrigerant and oil lowers cooling. Choose refrigeration oil by refrigerant compatibility, charge amount and miscibility.

  7. 07

    Strength testing and acceptance

    Assembled equipment is test-run to check hydraulic pressure, leaks, exhaust color and oil temperature. Equipment parked outdoors after testing lets moisture into the engine, rusting cylinder walls. Choose post-test protectants by rust protection duration and standing time.

  8. 08

    Painting and surface treatment

    Metal surfaces are cleaned, then rust preventive primer and urethane topcoat form a two-layer film. Scale and oxide on welds lift the coating there first. Choose the paint system by film performance and weld adhesion.

  9. 09

    Packing and transport

    Finished equipment is fixed in wooden frames and shipped by container or ro-ro vessel. At sea, salt and moisture get into engines and hydraulic piping. Choose rust protection by voyage length and exposed areas.

  10. 10

    Concrete formwork

    On construction sites, release agent is applied to formwork, concrete is poured and rebar is given rust protection. Uneven application leaves poor demolding and surface bubbles. Choose a release agent by release, application amount and formwork material.

  11. 11

    Asphalt paving

    Paving equipment lays and compacts asphalt while release agent is applied to equipment surfaces to prevent sticking. Uneven application lets asphalt stick and take time to clean. Choose release agents by anti-stick performance and seasonal viscosity.

Regulation and certification

  • ISO 4406

    The international standard expressing solid particle contamination in hydraulic oil as a code by particle size. Heavy equipment on dusty sites sets hydraulic oil and filter changes against the maker's cleanliness code.

  • ISO 15380

    The international specification for environmentally acceptable hydraulic fluids in the HETG, HEPG, HEES and HEPR categories. Sites near water or forest, where leaks reach the environment directly, use biodegradable fluids that meet it.

  • API CK-4

    The API performance category for high-speed four-stroke diesel engine oils. Makers of current construction machinery engines with exhaust aftertreatment often require this category.

  • Caterpillar TO-4

    Caterpillar's specification for oils in powershift transmissions, final drives and wet brakes. Mismatched friction properties can cause clutch and brake slip, so this equipment uses oils that meet the specification.

FAQ

Can biodegradable and mineral hydraulic oils alternate in the same machine?

It is often hard to recommend. The two families have different base oils, so additive behavior and reaction to water differ, and when previous fluid left in piping mixes in, faster degradation or seal swelling has been reported.

If you need to switch, it is safer to plan a flushing procedure. Biodegradable fluids go into sites that separately require environmental certification data, so confirmed mixing can undermine that machine's certification basis. Recording color changes and leak points during initial operation after the change helps tell later whether a problem comes from mixing or from seals.

Excavator hydraulic oil turns black quickly. Should we move up to a higher grade?

It is too early to treat it only as an oil type issue. When oil temperature stays high through load tests or continuous summer work, oxidation speeds up, and the same symptom appears when the oil cooler is clogged with soil and cannot cool. Excavators collect dust on the cooler face, so machines whose oil darkens quickly sometimes cluster at certain sites.

Color alone is hard to judge, so it is better to look at oil temperature and acid number as well. If oil temperature does not drop after the cooler is cleaned, fluid degradation or the circuit is likely; if cleaning alone restores it, cooling was likely the cause.

Do we have to use low-ash engine oil, or can we keep using our current oil?

For engines with aftertreatment, it is safer to keep to the specification. Oil high in ash, phosphorus and sulfur leaves ash in the diesel particulate filter and shortens regeneration intervals, and repeated cases have led to filter replacement.

Going outside the oil specification used in certification testing also puts emission certification at risk. So substitute proposals are often reviewed only after grade labels and the equipment maker's approved list are in place, and even at a lower price, a product missing these two is not compared. Including filter replacement cost can reverse the oil price difference.

Grease on the tracks washes out within days. Should we use a harder product?

Raising consistency alone often does not solve it. Track drives take soil and water together, so the film stays only with both water resistance and adhesion to metal.

Raising consistency also increases pumping resistance in winter, so grease may not be pushed into where it is needed. When greasing takes longer on site, intervals get skipped, and soil gets in during the gap, speeding wear further. It is more practical to match water resistance and adhesion first, and choose within the range your lubrication equipment can push.

Tested equipment sits for months. How is the inside of the engine protected?

External rust protection alone is often not enough. Moisture can enter the engine while it sits and rust cylinder walls, so the usual setup combines storage rust preventive oil or volatile corrosion inhibitor materials.

Where it stands matters too. Under a roof or outdoors, the same protectant lasts different lengths of time, and starting and stopping repeatedly creates new condensation inside each time. For equipment parked for months, decide first whether to run it periodically to set the protection level; if it will not be run, the protectant grade is set higher.

Paint peels only around welds. Is it the paint?

Pretreatment is more likely than the paint. Welds tend to retain scale and oxide film, so cleaning and conversion coating do not form evenly, and the coating often lifts from there first.

Changing paint tends to add approval testing and cost. Weld areas have a different substrate condition, and in some cases adjusting only pretreatment conditions while keeping the paint resolves it. The usual order is to check first whether the post-weld scale removal step has been shortened under line takt pressure, and whether the conversion coating forms at the same thickness there.

Release agent spray is uneven in winter. How do we control it?

Viscosity often rises at low temperature and disrupts the spray. Diluting arbitrarily improves the spray but also lowers anti-stick performance, which can come back as asphalt sticking in the compaction section. Checking first for a seasonal specification is the right order.

Sprayer conditions matter too. Changing only the product while keeping nozzle size and pressure tends to repeat the symptom, and areas with thicker application show in pavement surface quality. Keeping a winter application rate into spring can leave stains on the finished surface, so it is good to decide on resetting settings when seasons change.

How do we check if rust protection materials for export require notification?

Look at ingredients and destination country together. The Act on the Registration and Evaluation of Chemicals, the destination's registration system and dangerous goods sea transport rules each apply separately, so passing one does not settle the others.

Flammable materials change sea transport classification, which also changes packing method and stowage conditions. Choosing materials on rust protection performance alone and then hitting a classification issue means redoing packaging, so it is easier on the schedule to choose materials and design packaging at the same time. The destination's registration system is checked again regardless of whether domestic requirements are settled.