KALTEC

BlogApplication notes

Why is carbon building up on my high-temperature chain?

Type
Application notes
Published
20 November 2026
Prepared by
Technical team
Product group
Equipment/Service Lubricants

Putting on more oil is the usual response to carbon on a chain, but oil that never reaches the joints bakes on the surface and adds to the residue. What actually builds carbon can be heat beyond the oil's limit, oil made heavy by evaporation, a base oil unsuited to the temperature, the wrong amount or interval of oiling, or old residue left uncleaned, and two or more can act at once.

Sometimes the plates and rollers of a chain running through an oven or dryer gather a thick black residue that comes back within days of oiling. It starts as a brown film that smears on the hand, darkens, and ends as a hard layer that has to be scraped off. Flakes of it can fall onto the product passing below. It may look like mere dirt, but this layer cuts both the chain's life and the line's running time.

A chain's life is decided at the joint where pin meets bushing. As the inside of the joint wears, the pitch, the distance between neighbouring pin centres, grows, so the chain lengthens and meshes poorly with the sprockets (Hogan, 2011; Rank et al., 2023). The lubricant's job is to keep a film inside this joint so metal does not touch metal, and the joint is the hardest place to reach from outside (Hogan, 2011). When residue blocks the joint opening, fresh oil cannot get in, and wear goes on even though the chain is being oiled. As the chain stretches, replacement comes sooner. One guide advises replacing drive chains on sprockets with fewer than 60 teeth once elongation, measured over at least six pitches, reaches 1.5% (Hogan, 2011).

The loss does not stop at the chain. Oil that breaks down at high temperature gives off vapour in the form of smoke along with solid residue; the smoke condenses on cooler parts of the equipment and degrades again, and the solids get in the way of heat transfer and lubrication, so the line stops again and again for cleaning (Mousavi et al., 2005). In ovens where the chain runs close to product, falling residue becomes a quality problem, and in food processing the lubricant must also be one permitted for incidental food contact (FDA, n.d.). Smoke and oil mist are also something workers breathe in (NIOSH, n.d.).

The residue is lubricant that has burned and been left behind. Heated in air, the oil oxidises and its molecules cling together, its light fractions boil off, and it passes through a sticky film into a hard carbon layer (Hong & Jang, 2023; Mousavi et al., 2005). So with the same oil, the amount of residue varies widely with the temperature the chain sees, the base oil, how much oil goes on and how often, and how the chain is cleaned.

In such cases the technical team sets up the five hypotheses below and rules them out one by one. The start is always the same: measure the surface temperature at the hottest point the chain actually passes, and compare it with the base oil and rated temperature range on the technical data sheet, the TDS. That one comparison screens several hypotheses at once.

Hypothesis 1: too hot

Temperature is the first thing to suspect, because a single thermometer answers it. It arises where the chain runs right beside a heat source, as in paint-curing ovens, baking ovens and heat-treatment furnaces, and it tends to surface when the process temperature is raised or the line is slowed so the chain stays longer in the hot zone. Suppose a new product that needs a hotter bake starts running through the same oven. A few weeks later the plates on the side facing the heaters begin to carry a brown film, which slowly hardens and turns black. The side facing away is still clean.

The brown film hardening into black follows the steps of oxidation. Heated oil molecules lose hydrogen and become free radicals, highly reactive fragments. A radical meets oxygen from the air and becomes a peroxy radical, which pulls hydrogen from another oil molecule, so the reaction runs on like a chain. The peroxides that build up then split, giving oxidation products such as aldehydes, ketones and carboxylic acids (Hong & Jang, 2023; Mortier et al., 2010).

These oxidation products are polar, with their electric charge lopsided, so they dissolve poorly in oil and stick together into larger molecules. Small molecules joining into large ones in this way is called polymerisation. As it goes on the oil thickens, and further heating turns it through a gel into solid residue (Mousavi et al., 2005). A study that heated polyol ester lubricants at 220 °C likewise measured heavy products, made of two or more joined molecules, growing stage by stage (Mousavi et al., 2005). The residue starts as a sticky brown film known as varnish, and with more heat it loses hydrogen and oxygen and sets into a hard black carbon layer (Hong & Jang, 2023).

Temperature sets the pace of all these reactions. By the Arrhenius law, which links reaction rate to temperature, the field rule of thumb is that oil oxidation roughly doubles, and oil life halves, with every 10 °C rise (Khonsari & Booser, 2003; Whitby, 2009). It is not an exact law, and the change grows larger at higher temperatures (Khonsari & Booser, 2003). The antioxidants that slow oxidation are used up along the way, so residue climbs steeply once they run out (Hong & Jang, 2023; Whitby, 2009).

What has to be measured is not the set point but the temperature the chain actually sees. Take the peak surface temperature of the chain with a contact or infrared thermometer, and log it regularly at the same point while the line runs. Also see whether residue builds up first where the heat is greatest, such as the side facing the heaters, and thins out further from the heat. The colour and hardness of the residue show how far it has gone: a brown sticky film is early oxidation, and a black crumbly layer is fully carbonised (Hong & Jang, 2023). To compare the deposit tendency of different oils, ask suppliers for thin-film deposit test results, in which a thin film of oil runs over a heated metal surface and the deposit is weighed. The standard was written for engine oil, but the principle is the same (ASTM International, 2025).

When the actual peak is near or above the top of the oil's rated range, there are two routes. One is a high-temperature oil with headroom above that limit; the other is an equipment change that cuts the chain's peak by even a few degrees, such as heat shields, a new chain route or a cooling section. A 10 °C difference changes the oxidation rate a great deal (Khonsari & Booser, 2003; Whitby, 2009), so even a few degrees count. Synthetic oils such as polyol esters oxidise at high temperature too (Cao et al., 2025), so look at lowering the temperature even when the oil is changed.

Hypothesis 2: oil boiled off

If oil dries off soon after application even though the temperature is within the rated range, look at evaporation. It shows up with spray nozzles that lay down a thin film, in long continuous ovens where the chain dwells in the heat, and on lines that run all day without a break. On the floor it looks like this: a chain oiled in the morning looks dry again before midday, white smoke drifts from the oven exit for a while after each application, and round the joints only a dark, sticky film remains where the oil was.

Oil dries fast because it is not made of a single kind of molecule. It is a mix of components of different sizes, and a thin film on a chain has a large surface, so at high temperature the low-boiling light fractions leave first. The remaining oil grows heavier and thicker, stops flowing into the joints, and goes on oxidising and polymerising where it sits (Mortier et al., 2010; Mousavi et al., 2005). One model holds that a lubricant at high temperature is lost three ways, by evaporation, oxidation and thermal decomposition, and in a thin film on a chain all three happen at once (Mousavi et al., 2005).

A high flash point does not mean low evaporation. One study spread eight additive-free base oils 30 to 50 μm thick on steel and heated them at 130 to 140 °C for 30 to 80 hours. The mineral oils lost some fractions early and then evaporated less, while PAO, a synthetic hydrocarbon, polyglycol and polyol ester lost little at first and later released large amounts of volatiles. After about 10 to 15 hours the synthetic and bio-based oils, with much higher flash points, were evaporating more than the mineral oils, and some lost more than 30 wt% (Stoncius et al., 2013). Short evaporation tests alone do not show the evaporation that comes with long heating and degradation.

The first signs to watch are smoke and how fast the oil dries. Heavy smoke right after application and oil that dries quickly mean high evaporation loss. If oil use rises at the same output, suspect evaporation and fling-off together, and log monthly consumption to see the trend. For numbers, use standard evaporation tests. The Noack method measures a lubricant's evaporation loss as percent by mass (ASTM International, 2021), and another method measures the evaporation loss of greases and oils between 100 and 150 °C (ASTM International, 2024). Values from different methods cannot be compared, so ask every supplier for the same method and set the results side by side.

Once evaporation is judged to be high, change how the oil is chosen. Do not rely on flash point alone; ask for evaporation loss and for deposit results from long tests at the actual operating temperature (Stoncius et al., 2013). Look again at where the oil goes on, too. If the chain passes a cooler point on its circuit, apply oil there, so it has time to soak into the joints before it evaporates.

Hypothesis 3: wrong base oil

Suspect the base oil when, on the same line, only the chain running through the hot zone builds residue that hardens unusually fast. It becomes a problem where one general chain oil is used across the whole plant, where an oil chosen for room temperature stays in use after the equipment changes, and where oil has been chosen on price or availability. Think of a newly installed dryer whose chain gets the same general-purpose oil as the existing conveyors. The chains at room temperature are fine, but the chain inside the dryer gradually disappears under a black layer that has to be scraped off.

Why an oil that holds up at room temperature fails only in the hot zone comes down to how much heat its base oil can take. The base oil makes up most of the lubricant and decides how well it stands up to heat and oxygen. Mineral oil is a mix of many hydrocarbons, so its light fractions leave easily at high temperature and its less stable components react first to form residue. Synthetic esters and PAO have more uniform molecules and better resistance to heat and oxidation, so they are used for high-temperature duty (Mortier et al., 2010; Rudnick, 2020), and polyol esters have such good oxidative stability that they are widely used in severe service such as aircraft engines (Cao et al., 2025).

Synthetic oils are not free of residue, though. Polyol esters still oxidise at high temperature, so antioxidants are added. In a study that oxidised a polyol ester containing a high-temperature amine antioxidant, N-phenyl-α-naphthylamine, heavy multi-ring compounds formed when antioxidant molecules joined together were the key cause of sludge, the sticky deposit that settles in the oil (Cao et al., 2025). Two polyol ester products of the same chemistry also degraded very differently at 220 °C (Mousavi et al., 2005). The exact molecular structure and additive package matter as much as the base oil class.

Check the base oil on paper first. Find the base oil type and rated temperature range on the TDS and on the safety data sheet, the SDS, and set them against the peak temperature the chain actually sees. Record the nature of the residue as well. Note whether it is soft and wipes off or is a hard carbon layer that must be scraped, and read a hard layer that forms quickly as a sign that the base oil cannot take the temperature (Mousavi et al., 2005). If there are candidate oils, put two or three on metal plates heated under the same conditions and compare the amount and hardness of residue after a set time, alongside standard thin-film deposit results if they exist (ASTM International, 2025).

The fix is a base oil that suits the temperature. Starting with the zones where the peak is beyond what mineral oil can take, consider a high-temperature chain oil based on synthetic ester or synthetic hydrocarbon. Before switching, ask the supplier for evaporation loss and deposit results at the actual operating temperature, and since synthetic oils differ from product to product, choose on the results of a side-by-side trial. In food processing, also confirm that the product meets the rules for incidental food contact (FDA, n.d.).

Hypothesis 4: wrong oiling

Look at the oiling when the oil and temperature are fine but oil drips below the chain or, the other way round, the joints are bone dry. It arises where the automatic lubricator settings were left alone after a change in line speed, where operators oil by feel with a brush or oil can, and where the nozzles point at the outer plate faces instead of the joints. Take a line whose automatic lubricator was set to a generous output: oil that drips onto the floor and guide rails below bakes black, and thick residue grows only on the outer plate faces. A look into the joint gaps may even find them dry.

In chain lubrication, the only useful oil is the oil that gets inside the joints (Hogan, 2011). Too much at once leaves oil that never entered the joints sitting thick on the plates and rollers, fully exposed to the heat, where it oxidises, evaporates and becomes residue (Mousavi et al., 2005). Oil that drips off also burns on the floor of the equipment and on nearby parts. In bath lubrication, too, running the chain too deep is said to overheat the oil and degrade it (Hogan, 2011).

If the interval is too long, the film inside the joint oxidises all the way into a hard layer that blocks the path for fresh oil. With too little oil in the joint, wear from sliding between pin and bushing increases, and abrasive wear, the main form of chain wear, goes on (Amiruddin et al., 2020; Rank et al., 2023). The iron fines from that wear then act as a catalyst that speeds up oil oxidation (Hong & Jang, 2023).

Over- and under-oiling leave different traces. Over-oiling shows as oil dripping below the chain, thick residue on the outer plate faces and heavy smoke right after application. Under-oiling shows as dry joints, red rust powder and a chain that stretches quickly, so measure length over at least six pitches regularly and log the elongation (Hogan, 2011). On an automatic lubricator, check the output, the interval and whether the nozzles point at the gap between pin and plate by looking at them directly.

What needs fixing is placement and interval more than amount. Aim the nozzles at the gap between pin and plate, and shift toward small amounts more often rather than a lot at once. If oil drips, cut the amount per shot; if the joints dry out, shorten the interval. After any change, log elongation, oil consumption and the state of the residue together for some weeks to see the effect.

Hypothesis 5: overdue cleaning

When the oil and the oiling have been put right and the residue still does not shrink, what remains to suspect is the residue already there. It arises on lines where cleaning has been put off because production is hard to stop, on lines where the oil was changed without removing old deposits, on lines with a lot of process dust such as flour or paint particles, and on lines where different products have been applied over one another. A bakery oven chain is a typical scene. Fresh oil has gone on over the old for a long time without cleaning, and a flake of residue broken off and viewed in section shows several layers with flour caught between them.

Old residue hastens the breakdown of fresh oil. Fresh oil put on over uncleaned residue stays on the old deposit rather than reaching the joints, and burns there with it. Varnish-type deposits hold wear particles on their surface, and these trapped hard particles, along with metals such as iron and copper, help break down peroxides and act as catalysts that speed up oil oxidation (Hong & Jang, 2023). Oxidation products left in already oxidised oil also get the chain reaction in fresh oil going sooner (Hong & Jang, 2023; Mortier et al., 2010).

Dust, flour and paint particles from the process mix with the oil into a paste and set with it at high temperature, adding to the residue. If this mix gets into the joints it works like an abrasive and increases abrasive wear (Amiruddin et al., 2020; Rank et al., 2023). Mixing different products leaves a base oil and additive blend that neither was designed as, so neither product's test results can be counted on.

A single flake of residue tells a lot. Several layers in its cross-section mean oil has gone on over old deposit again and again. If it wipes off with a solvent such as acetone it is varnish; if it will not wipe and must be scraped, it is a carbonised layer or lacquer (Hong & Jang, 2023). Check the SDS before using any solvent, and use it only once the equipment is cool. Look under a magnifier for process powder, fibre or metal fines, and check the records for cleaning history, product changes and any mixing.

Here cleaning comes before oil. When changing oil or when the residue is thick, clean the chain to remove the old deposits first, then apply fresh oil, and oil more often for the first few applications after cleaning to refill the joints. Use one product per chain, and in dusty zones consider covers or dust extraction as well.

Testing the hypotheses

Five hypotheses do not call for five investigations at once. Rule them out one at a time, starting with what a thermometer and the paperwork answer straight away.

The first step is temperature and paperwork. Measure the real surface temperature at the hottest point on the chain's path, and check it against the base oil and rated range on the TDS and SDS. A peak near or above the top of the range puts hypothesis 1 on the list; a general mineral oil in a hot zone puts hypothesis 3 there. This one comparison screens out much of hypotheses 1 and 3.

Next, look at where the residue forms and what it looks like. Recording its location, colour, hardness, solvent response and layering, with photos, reveals a great deal about the cause (Hong & Jang, 2023). Residue gathered where the heat is greatest, such as the side facing the heaters, points to hypothesis 1; heavy smoke after application and oil that dries fast, to hypothesis 2; thick build-up on the outer plate faces and below the chain, or dry joints, to hypothesis 4; and layers with process dust in the cross-section, to hypothesis 5.

If that still does not settle it, run a control test. Clean one section of the chain, give it fresh oil only, and watch it for a few weeks beside a section left uncleaned. If only the cleaned section stays clean, hypothesis 5 is the main cause. If both foul just as fast, the cause lies with the oil and temperature, so compare the evaporation loss and thin-film deposit results of candidate oils by the same methods (ASTM International, 2021; ASTM International, 2025; Stoncius et al., 2013).

Once the cause is found and fixed, the last step is to confirm it in the trend. It is done only when, over the weeks after the fix, the residue and oil consumption improve and chain elongation stops speeding up (Hogan, 2011). Change one thing at a time and keep records, so it is clear which step made the difference.

One more thing to remember: the hypotheses can overlap. Near the temperature limit, evaporation and oxidation speed up together, and over-oiling and oil applied over old deposit then add to the residue. In such cases, fix temperature and base oil first, then clean the chain, then adjust the oiling; in that order the effect of each step is easiest to see.

Limits and cautions

Usable temperature and the right amount of oil differ by oil and by equipment, so numeric decisions follow the product's TDS and real tests. If the chain is already well stretched or the sprocket teeth are worn, changing the lubricant will not bring it back, so consider replacing chain and sprockets as well (Hogan, 2011). For food lines, large ovens and equipment with a fire risk, do not decide on floor judgement alone; get the equipment maker and a lubrication specialist to confirm.

Safety matters too. Smoke and mist from hot oil are an inhalation exposure. The United States National Institute for Occupational Safety and Health, NIOSH, sets a recommended exposure limit for mineral oil mist of 5 mg/m³ as an 8-hour time-weighted average (NIOSH, n.d.). Oil and clean with the SDS in hand, with ventilation, eye protection and gloves that resist heat and oil, and where possible with the equipment stopped and cooled. Never use flammable solvents on hot surfaces.

Sources

  1. Amiruddin, H., Abdollah, M. F. B., & Mohamad Nizar, M. A. D. (2020). Measurement of roller chain wear lubricated with palm oil-based hexagonal boron nitride nanoparticles. Industrial Lubrication and Tribology, 72(10), 1199–1204. https://doi.org/10.1108/ILT-02-2020-0061
  2. ASTM International. (2021). ASTM D5800-21, Standard test method for evaporation loss of lubricating oils by the Noack method. https://store.astm.org/d5800-21.html
  3. ASTM International. (2024). ASTM D972-24, Standard test method for evaporation loss of lubricating greases and oils. https://store.astm.org/d0972-24.html
  4. ASTM International. (2025). ASTM D7097-25, Standard test method for determination of moderately high temperature piston deposits by thermo-oxidation engine oil simulation test—TEOST MHT. https://store.astm.org/d7097-25.html
  5. Cao, C., Li, H., Han, S., & Li, J. (2025). Study on the formation mechanism of oil sludge in polyol esters in presence of high-temperature antioxidant N-phenyl-α-naphthylamine. Lubricants, 13(9), 403. https://doi.org/10.3390/lubricants13090403
  6. Hogan, M. (2011, May). Getting more life from roller chain. Machine Design. https://www.machinedesign.com/mechanical-drives/getting-more-life-roller-chain
  7. Hong, S.-H., & Jang, E. K. (2023). Varnish formation and removal in lubrication systems: A review. Materials, 16(10), 3737. https://doi.org/10.3390/ma16103737
  8. Khonsari, M., & Booser, E. R. (2003). Predicting oil and grease life. Machine Design. Republished by Machinery Lubrication. https://www.machinerylubrication.com/Articles/Print/537
  9. Mortier, R. M., Fox, M. F., & Orszulik, S. T. (Eds.). (2010). Chemistry and technology of lubricants (3rd ed.). Springer. https://doi.org/10.1007/978-1-4020-8662-5
  10. Mousavi, P., Wang, D., Grant, C. S., Oxenham, W., & Hauser, P. J. (2005). Measuring thermal degradation of a polyol ester lubricant in liquid phase. Industrial & Engineering Chemistry Research, 44, 5455–5464. https://doi.org/10.1021/ie049135u
  11. National Institute for Occupational Safety and Health [NIOSH]. (n.d.). Oil mist (mineral). NIOSH Pocket Guide to Chemical Hazards. https://www.cdc.gov/niosh/npg/npgd0472.html
  12. Rank, M., Oehler, M., Koch, O., Bobzin, K., Kalscheuer, C., & Möbius, M. P. (2023). Investigation of the influence of triboactive CrAlMoN coating on the joint wear of grease-lubricated roller chains. Tribology Transactions, 66(6), 1105–1116. https://doi.org/10.1080/10402004.2023.2264908
  13. Rudnick, L. R. (Ed.). (2020). Synthetics, mineral oils, and bio-based lubricants: Chemistry and technology (3rd ed.). CRC Press. https://doi.org/10.1201/9781315158150
  14. Stoncius, A., Liascukiene, I., Jankauskas, S., & Asadauskas, S. J. (2013). Volatiles from thin film degradation of bio-based, synthetic and mineral basestocks. Industrial Lubrication and Tribology, 65(3), 209–215. https://doi.org/10.1108/00368791311311213
  15. U.S. Food and Drug Administration [FDA]. (n.d.). 21 CFR 178.3570, Lubricants with incidental food contact. U.S. Code of Federal Regulations. https://www.law.cornell.edu/cfr/text/21/178.3570
  16. Whitby, D. (2009, November). Extending lubricant life. Tribology & Lubrication Technology. https://www.stle.org/images/pdf/STLE_ORG/BOK/OM_OA/Additives/Extending%20Lubricant%20Life_tlt%20article_Nov09.pdf

Product and site consultation

Leave your company, site and the product groups in use. Our engineer will get in touch to go through your site conditions and concerns. Materials, equipment, operating conditions and downstream steps show what should change and what can stay. If nothing needs to change, we will say so.

Contact us
After you contact us
  1. 01
    Site setup

    We confirm process conditions and needs first.

  2. 02
    Spec design

    We set the product spec and selection criteria.

  3. 03
    Comparison

    We compare matching candidates and propose.

  4. 04
    Tailored supply

    We supply on time and manage the stock.

  5. 05
    Site check

    We visit, check conditions of use and record.

  6. 06
    Use management

    We track use and change cycles to catch issues.

  7. 07
    Regular analysis

    We analyze the records and send a yearly report.