KALTEC

BlogApplication notes

Why has my grease hardened?

Type
Application notes
Published
20 November 2026
Prepared by
Technical team
Product group
Greases

Pumping fresh grease on top is the usual response to hardened grease, but hardened grease does not recover that way and whatever hardened it stays in place. What actually hardens grease can be heat oxidation, lost base oil, dust, long storage or mixing with another grease, and often two or more at once.

Sometimes a bearing housing opened for greasing turns out to hold grease that is no longer soft but hard. The grease gun barely pushes anything in, and what scrapes out has turned dark or gone crumbly and dry. If other points on the same grease are fine and only a few look like this, something about those points, or about the path the grease took, is at work.

Hardened grease cuts bearing life. Grease lubricates by releasing oil to form a film; hardened grease cannot release it, the film thins, friction rises and heat builds, which speeds oxidation and drying further in a loop (Fitch, n.d.). When the grease reaches the end of its life the bearing soon follows, so grease life is treated as a main factor in bearing life (Lugt, 2009, 2013). When the bearing stops the machine stops, and that costs far more than the grease.

Grease is a semi-solid in which base oil is held in a fibrous network called the thickener. The thickener holds the oil like a sponge and, as the bearing turns, releases it a little at a time to form a thin film on the metal, so most of the lubricating work is done by the oil (Lugt, 2009, 2013). Grease hardens for two broad reasons: the oil leaves and only the thickener remains, or heat and oxygen oxidise the oil and thickener and change their nature (Lugt, 2009; Rezasoltani & Khonsari, 2016). Hardness, or consistency, is measured by cone penetration: a standard cone sinks into the grease, the depth is read in tenths of a millimetre, a smaller number means harder grease, and the NLGI consistency grade is set from this value (ASTM International, 2021a).

In such cases the technical team sets up the five hypotheses below and rules them out one by one. The start is always the same: take a little of the hardened grease, note its colour, smell and feel, and record the running temperature at that point, the last greasing date and the manufacture date of the grease. That screens several hypotheses at once.

Hypothesis 1: heat oxidation

Oxidation happens at hot points. Typical ones are bearings near dryers or ovens, motor bearings running at high speed and bearings packed full because too much grease goes in. A fan motor bearing that gets several pumps of the grease gun out of habit at every greasing is one such point. Right after greasing the housing stays hot for a while, and the old grease pushed out at the next greasing is dark brown and sticky.

Grease degradation is either physical or chemical, and oxidation is the core of the chemical side. The antioxidant, an additive that reacts with oxygen first to protect the oil, is used up first, then the base oil and thickener oxidise (Rezasoltani & Khonsari, 2016). Once the antioxidant is spent, oil molecules react with oxygen in a chain, forming organic acids and carbonyl compounds, and some join together into larger molecules (Rezasoltani & Khonsari, 2016; Schneidhofer et al., 2025). These larger molecules make the oil steadily stickier, and the growing acids damage the thickener structure too. One study found that once the antioxidant is nearly used up, oil evaporation speeds up along with oxidation (Schneidhofer et al., 2025).

Temperature governs the oxidation rate. In the normal operating range, a rule of thumb says grease life roughly halves for every 15 °C rise (SKF, 2004), and at very high temperatures oxidation becomes the main factor limiting grease life (Rezasoltani & Khonsari, 2016). Over-greasing leads the same way. When the free space in a bearing is packed full, the rolling elements keep churning the grease, generating friction heat that speeds oxidation (Fitch, n.d.; Lugt, 2009).

Colour and smell are the first clues. The grease turns a deeper brown or black than new and smells burnt or sour, and rubbed between the fingers it is sticky rather than smooth or leaves a varnish-like film. If housing temperature runs above normal, or records show a sharp rise right after greasing, put this hypothesis first. In-service grease can be assessed for consistency, contamination and oxidation together by a method such as ASTM D7918 (ASTM International, 2023). New greases are compared for oxidation stability by the ASTM D942 oxygen pressure vessel or ASTM D5483 pressure differential scanning calorimetry, but neither test predicts service life directly (ASTM International, 2021b, 2025).

If running temperature is near the top of the grease's range, consider a grease rated for higher temperature and shorten the relubrication interval in line with the rise (SKF, 2004). If temperature climbs right after greasing, the charge is too large; cut it to the equipment maker's recommended amount. Do not pump new grease on top of hardened grease; where possible, open the housing, remove the hardened grease and refill, since leftover oxidation products can speed the oxidation of fresh grease (Rezasoltani & Khonsari, 2016).

Hypothesis 2: base oil loss

If the colour has hardly changed but the grease is dry, the base oil may have left it. This shows up on high-speed parts, high-vibration machines, hot spots and points fed by spring-type automatic lubricators. Take off the lubricator on a bearing beside a vibrating screen to replace it, and the canister often holds a layer of clear oil sitting apart from a waxy lump, with oil smears around the bearing.

The thickener cannot hold the oil forever. In service grease always releases a little oil, called oil separation or bleed (Lugt, 2009). Some bleed is needed for lubrication, but if it runs too fast the thickener share of what remains rises and the grease gets harder. The ASTM standard likewise states that when grease separates oil, the consistency of what remains increases (ASTM International, 2024a). Mechanical shear, the rubbing and tearing of grease by moving parts, can also break the thickener network; its grip on the oil then weakens, bleed accelerates, and the grease ends up dry and hard (Rezasoltani & Khonsari, 2016).

Oil leaves by two routes. One is evaporation: at high temperature the lighter fractions of the oil boil off, and the standards note that this evaporation loss can degrade a lubricant's original performance (ASTM International, 2024c, 2026). The other is force: prolonged vibration and centrifugal force separate the oil early, and devices that hold grease under constant pressure, such as spring-type automatic lubricators, squeeze oil out of the thickener (Fitch, n.d.). At high enough temperatures oil can boil out of the thickener and harden the grease over time (Fitch, n.d.).

Colour is what separates this from oxidation. Grease that is crumbly or waxy and dry with little colour change, with oil smears around it, points here; clear oil and hard lumps sitting apart inside a lubricator canister point to pressure-driven separation. A laboratory compares new and used grease by cone penetration (ASTM International, 2021a), and checks the evaporation tendency of new grease by ASTM D972, run at 100 to 150 °C, or ASTM D2595, which covers a wider range. Results of the two tests are not interchangeable (ASTM International, 2024c, 2026).

On hot points, consider a grease made with a lower-evaporation base oil; on high-speed points, recheck the base oil viscosity and consistency grade the equipment maker recommends. Set automatic lubricators to dispense more often so grease does not sit in the canister for long, and check the contents of any unit left idle for a long time (Fitch, n.d.). A little separated oil on the grease surface can be normal, so judge by whether hard lumps have formed (Fitch, n.d.).

Hypothesis 3: dust contamination

At dusty points grease takes up powder and stiffens. It happens on dusty sites such as cement, foundry, timber and mining operations, on bearings with damaged seals and at points where the grease nipple is dirty. Scrape grease from a conveyor bearing near a foundry's shot-blast unit, and its original colour is gone, turned a cloudy grey-brown.

Contamination is one of the main routes of grease degradation (Rezasoltani & Khonsari, 2016). When a lot of dry powder such as dust, dirt or fly ash gets in, the grease thickens as if more gelling agent had been added (Fitch, n.d.). Very fine powder has a large surface area and pulls oil onto its surface, so less oil stays in the thickener network and the grease dries out (Fitch, n.d.). The more powder, the more the grease becomes a paste that cannot release oil, and at the same time it scours surfaces like an abrasive.

Read the feel and the location together. Grit between the fingers, at a dusty point with worn seals, makes this the strong hypothesis. A laboratory can confirm dirt by elemental analysis, and ASTM D7918 sets out how to assess contamination and consistency of in-service grease together (ASTM International, 2023).

What needs blocking is the way the powder gets in. Wipe the nipple and the grease gun tip before greasing, and fit nipple caps. Open grease containers only when in use and close them straight away (Ludwig, n.d.). Check seal condition, and in dusty areas shorten the relubrication interval so fresh grease purges the contaminated grease. Grease already hardened with powder will not recover by topping up; remove it and refill.

Hypothesis 4: long storage

Grease changes even when it is not used. Typical are stores where stock sits for a long time, sunny shelves and pails kept near heaters or drum warmers. Open an old cartridge found at the back of the store: oil has pooled on top, and underneath it is too hard to push a finger into.

Even inside the container, oil separates slowly, at a rate that depends on storage temperature and time, vibration in transport and storage, and how uneven the grease surface in the container is (Ludwig, n.d.). ASTM D1742 measures exactly this tendency to separate oil in storage, and states that its results correspond directly to the separation that occurs in stored pails. The grease left behind under the separated oil becomes firmer (ASTM International, 2024a).

Apart from oil separation, some greases firm up as the thickener structure rearranges itself over time. This is called age hardening, and how much it happens depends on storage time, temperature and the nature of the product (Ludwig, n.d.). Direct sunlight, nearby heat sources and overheated drum warmers speed up oil separation and thicken the grease (Ludwig, n.d.).

The lot number is the clue. If the equipment is fine but hard grease comes only from one lot, suspect storage. Check the manufacture date or lot number on the container and the temperature where it was kept, and see whether a freshly opened pail has oil pooled on top or differs in firmness from top to bottom. A laboratory compares unworked penetration with penetration after a set amount of working to see how storage affected consistency (ASTM International, 2021a).

Store grease somewhere cool and dry, and use the oldest stock first. Keep it indoors no warmer than 30 °C, keep cartridges upright, and keep drums and pails off the floor and sealed (Ludwig, n.d.). There is guidance to inspect grease older than a year before use (Ludwig, n.d.), so check old stock for penetration or appearance first. A little oil pooled on top can be poured off or stirred back in, but do not use grease that has lumped or changed firmness markedly (Ludwig, n.d.).

Hypothesis 5: mixed greases

Mixing tends to happen right after a change to another grease, or on sites where several workers carry their own grease guns. After a change of supplier brings in a new grease, the same bearing is opened to show two greases of different colour and texture streaked together, with lumps and runny parts side by side.

Each grease has a thickener, base oil and additives balanced to work together. Mixing in another grease adds unplanned ingredients that can upset this balance and degrade performance, a chemical effect that depends on concentration and temperature (Samman, n.d.). Different thickeners can collapse each other's fibre structure, and base oils that do not mix well separate (Samman, n.d.).

The most common results of mixing are softening, oil separation and a lower dropping point, the temperature at which grease melts and drips (Samman, n.d.). Yet ASTM D6185 notes that mixtures occasionally harden, and conversely can soften so much that they run out of an operating bearing (ASTM International, 2024b). If oil separates from the mixture, it can also leave a hardened thickener behind, as in hypothesis 2. Which pairs are compatible is generally hard to predict and must be confirmed by testing (ASTM International, 2024b).

Trace back through the work records. Check every grease that went into that point, and match when the grease was changed with when it began to harden. Compatibility is judged by mixing the two greases at several ratios and comparing consistency, dropping point and shear stability, as in ASTM D6185 (ASTM International, 2024b).

When changing grease, remove as much of the old grease as possible and purge thoroughly with the new one. Label or colour-code grease guns and containers so each point receives only one grease. If mixing cannot be avoided, have a compatibility test done beforehand, and shorten the relubrication interval right after the change to watch the condition (ASTM International, 2024b; Samman, n.d.).

Testing the hypotheses

A lump of grease in the hand and a few records go a long way towards sorting the five hypotheses. Work through them in turn, starting with the easiest comparisons.

Start with new grease. If unopened pails or cartridges from the same lot are also hard, the issue is storage, hypothesis 4, not the equipment. If the new grease is fine, look at the colour and smell of the hardened grease. Dark brown or black with a burnt or sour smell means oxidation, hypothesis 1; grit between the fingers and an earthy colour mean dust, hypothesis 3.

If the colour has barely changed but the grease is dry, move to equipment conditions and temperature records. High speed, heavy vibration or an automatic lubricator point to oil loss, hypothesis 2; high running temperature or a rise right after greasing points to oxidation and evaporation together. A recent change of grease, or a second grease in the point, sends you to hypothesis 5. If the grease is stiff only in winter or cold places and returns to normal when warmed, the cause is low temperature, not degradation; check that the grease suits that temperature.

If the picture is still unclear, use a control sample. Send the used grease together with new grease of the same product to a laboratory and compare consistency, oxidation and contamination side by side (ASTM International, 2023). After the fix, remove all hardened grease, refill and check the condition at the same intervals; the job is done only when the grease no longer hardens.

Two or more causes can also stack up. Over-greasing brings heat and oxidation, oxidation weakens the thickener and speeds oil loss, and dusty points often have damaged seals and heat as well (Fitch, n.d.; Rezasoltani & Khonsari, 2016). When causes stack up, fix first the one that feeds the others, such as heat.

Limits and cautions

Follow the equipment maker for relubrication interval and amount, and the grease's product data for temperature range and consistency grade. Colour, smell and feel are easy clues only, and can look different depending on the thickener and base oil. For most laboratory tests no correlation with service life has been established, so use them to compare products, not to predict life directly (ASTM International, 2021a, 2021b, 2024c, 2025).

Stop and lock out the equipment before removing hardened grease. Wear oil-resistant gloves to avoid long skin contact, and when using cleaning solvents follow the protective equipment and ventilation set out in that product's safety data sheet, the SDS. If bearing noise, vibration and temperature rise are already present together, do not stop at changing the grease; have a specialist who can assess bearing condition take over.

Sources

  1. ASTM International. (2021a). ASTM D217-21, Standard test methods for cone penetration of lubricating grease. https://store.astm.org/d0217-21.html
  2. ASTM International. (2021b). ASTM D5483-21, Standard test method for oxidation induction time of lubricating greases by pressure differential scanning calorimetry. https://store.astm.org/d5483-21.html
  3. ASTM International. (2023). ASTM D7918, Standard test method for evaluation of in-service grease. Current edition. https://dinmedia.de/en/standard/astm-d-7918/375376744
  4. ASTM International. (2024a). ASTM D1742-24, Standard test method for oil separation from lubricating grease during storage. https://store.astm.org/d1742-24.html
  5. ASTM International. (2024b). ASTM D6185-24, Standard practice for evaluating compatibility of binary mixtures of lubricating greases. https://store.astm.org/d6185-24.html
  6. ASTM International. (2024c). ASTM D972-24, Standard test method for evaporation loss of lubricating greases and oils. https://store.astm.org/d0972-24.html
  7. ASTM International. (2025). ASTM D942-25, Standard test method for oxidation stability of lubricating greases by the oxygen pressure vessel method. https://store.astm.org/d0942-25.html
  8. ASTM International. (2026). ASTM D2595-26, Standard test method for evaporation loss of lubricating greases over wide-temperature range. https://store.astm.org/d2595-26.html
  9. Fitch, J. (n.d.). Grease dry-out: Causes, effects and remedies. Machinery Lubrication. Noria Corporation. https://www.machinerylubrication.com/Articles/Print/28517
  10. Ludwig, L. G. (n.d.). Storing grease to avoid bleed and separation. Machinery Lubrication. Noria Corporation. https://www.machinerylubrication.com/Articles/Print/28761
  11. Lugt, P. M. (2009). A review on grease lubrication in rolling bearings. Tribology Transactions, 52(4), 470–480. https://doi.org/10.1080/10402000802687940
  12. Lugt, P. M. (2013). Grease lubrication in rolling bearings. Wiley. https://www.wiley-vch.de/en/areas-interest/engineering/grease-lubrication-in-rolling-bearings-978-1-118-35391-2
  13. Rezasoltani, A., & Khonsari, M. M. (2016). On monitoring physical and chemical degradation and life estimation models for lubricating greases. Lubricants, 4(3), 34. https://doi.org/10.3390/lubricants4030034
  14. Samman, N. (n.d.). A review of grease compatibility. Lubrication Fundamentals. Society of Tribologists and Lubrication Engineers. https://www.stle.org/Shared_Content/End_Users/Lube_Fundamentals/Grease_Articles_FULL/A_Review_of_Grease_Compatibility.aspx
  15. Schneidhofer, C., Schandl, M., Dörr, N., & Lugt, P. M. (2025). A model describing the oxidation rate of lubricating greases. Frontiers in Mechanical Engineering, 11, 1591795. https://doi.org/10.3389/fmech.2025.1591795
  16. SKF. (2004). Grease life in lubricated-for-life deep groove ball bearings. Evolution. https://evolution.skf.com/grease-life-in-lubricated-for-life-deep-groove-ball-bearings/

Product and site consultation

Leave your company, site and the product groups in use. Our engineer will get in touch to go through your site conditions and concerns. Materials, equipment, operating conditions and downstream steps show what should change and what can stay. If nothing needs to change, we will say so.

Contact us
After you contact us
  1. 01
    Site setup

    We confirm process conditions and needs first.

  2. 02
    Spec design

    We set the product spec and selection criteria.

  3. 03
    Comparison

    We compare matching candidates and propose.

  4. 04
    Tailored supply

    We supply on time and manage the stock.

  5. 05
    Site check

    We visit, check conditions of use and record.

  6. 06
    Use management

    We track use and change cycles to catch issues.

  7. 07
    Regular analysis

    We analyze the records and send a yearly report.