KALTEC

BlogApplication notes

Why does aluminium stain after machining?

Type
Application notes
Published
20 November 2026
Prepared by
Technical team
Product group
Metalworking Fluids (MWF)

It is easy to assume that a coolant set at high pH to stop steel rusting will protect aluminium too, but alkali dissolves the very oxide film that guards aluminium. What actually stains the metal can be high pH, too little inhibitor, poor make-up water, parts left wet, or galvanic corrosion between metals, and two or three of these can act at once.

A freshly machined aluminium part comes out clean, yet after the wash station or a night in a stack it shows a faint yellow mark or a spreading grey stain. Same machine, same coolant, and some days are fine while others are not, and the severity changes with the alloy. A stain that will not wipe off most likely means a chemical change has already taken place on the surface.

Stains range from light yellow to very dark grey (Canter, 2020), and they are more than a cosmetic flaw. Where the oxide film has dissolved or broken, corrosion can go further, and the adhesion and colour of later finishes such as anodising or painting change (Vargel, 2020). Parts caught at visual inspection go back for sorting and rework, and stains that only show after finishing turn into rejects.

Aluminium is a highly reactive metal, yet a few nanometres of aluminium oxide form the moment it meets air and protect the metal beneath. The film is stable roughly around neutral; in strong acid it dissolves as aluminium ions and in alkali as aluminate ions. A Pourbaix diagram, which plots pH against potential, the readiness of a metal to give up electrons and dissolve, sets this out (Deltombe & Pourbaix, 1958; Vargel, 2020). Water-mix coolant, however, is usually formulated above pH 9 to stop steel rusting and bacteria growing (Canter, 2020). The conditions that protect steel and those that protect aluminium pull apart from the start, so weekly checks of concentration and pH, the basics of coolant care, are also where aluminium staining is diagnosed (HSE, 2021).

In such cases the technical team sets up the five hypotheses below and rules them out one by one. The start is always the same: note whether stains appear during machining, after washing or in storage, then measure pH on a calibrated meter and concentration on a refractometer in the stained sump, and compare both with the supplier's recommended range.

Hypothesis 1: pH too high

Start with this hypothesis in plants that alternate ferrous and aluminium parts on one sump, on lines that run the mix rich, and in systems where evaporation pushes sump concentration up on its own. Picture a machining centre that has been cutting steel shafts and now takes on aluminium housings. The housings are cut in the same coolant, set to keep steel from rusting, and after a day or two on the rack a yellowish stain has spread evenly, starting on the inner faces where coolant pooled longest.

High pH leaves a stain in three steps. First, hydroxide ions in the coolant react with the aluminium oxide film to form aluminate ions, which dissolve in water. The film dissolves faster as pH rises, and even at a fixed pH, film growth and film dissolution run side by side (Vargel, 2020; Walkner et al., 2016). Where the film has thinned, the metal reacts directly with water, releasing hydrogen as it dissolves, and a loose, porous hydroxide layer builds up on top (Hart, 1957; Vargel, 2020). This new layer is thicker and less even than the original film, so it reflects light differently, and mixed with alloying elements it looks yellow, brown, grey or black (Canter, 2020; Vargel, 2020).

The main pH raisers are amines, notably alkanolamines, amines carrying alcohol groups. Amines neutralise acidic components and hold the pH, but they are not aluminium stain inhibitors in themselves, and some types push pH higher and increase stains and residues (Canter, 2020). When water evaporates from the sump and concentration rises, the amines concentrate as well and pH tends to climb (Byers, 2017; HSE, 2021).

Two tools settle it: a calibrated pH meter and a refractometer. Take a sample from the stained sump, read pH and refractometer concentration, and compare both with the supplier's recommended range, keeping strips for trends only. If concentration and pH are both high, evaporation has thickened the fluid; if concentration is right but pH alone is high, the product's own pH may not suit that alloy. Measure at least weekly, and on the day stains appear (HSE, 2021). Stains spread evenly over faces that sat longest in coolant, or where it pooled, add weight to this hypothesis.

Where high concentration is behind it, top up with water or a weak mix instead of concentrate and bring concentration back first (HSE, 2021). If pH still exceeds the supplier's upper limit for aluminium at the right concentration, do not push it down with acid or additives; confirm with the supplier whether the product is formulated for aluminium. If one sump serves both steel and aluminium, check the supplier's test data to see that the product suits both metals (Byers, 2017; Canter, 2020).

Hypothesis 2: too little inhibitor

If pH is within the recommended range and stains still appear, turn to the inhibitors that protect aluminium. This shows up in sumps that have run lean on water-only top-up, in systems used for months on make-up alone without a change, and where a fluid chosen for steel is used on aluminium as it is. As a scene: two machines run the same product, parts from the one recharged last month come out clean, and only parts from the long-running sump show stains.

Aluminium inhibitors work in three ways: they bond chemically to the surface by adsorption and form a thin protective layer, they capture corrosive species in solution, or they cover the metal with a physical film (Canter, 2020). Phosphorus-based inhibitors such as phosphate esters are reported to chemisorb into a thin barrier with broad effect, and silicates are used mainly above pH 9 (Canter, 2020). Silicate is explained as attaching to the negatively charged aluminium oxide surface as aluminosilicate and reinforcing the film (Rosalbino et al., 2024).

The catch is that these components are used up in service. When heavy water top-up thins the mix, the inhibitors thin with it and no longer cover the whole surface (Byers, 2017; HSE, 2021). Even at normal concentration, inhibitors adsorb onto chips and part surfaces and leave with them, and silicates can precipitate over time and block filters (Byers, 2017; Canter, 2020). A refractometer shows the strength of the whole mix, not how much inhibitor is left, so a correct reading does not clear this hypothesis. A fluid carrying only steel inhibitors never forms a layer over aluminium in the first place.

First see whether refractometer concentration has dropped below the recommended minimum. If it has not, a coupon immersion test sorts this out. Half immerse clean coupons of the alloy being machined in fresh mix and in sump fluid set to the same concentration, and leave them for 24 to 48 hours at room temperature, or at 40 to 50°C for a harsher test. Afterwards, compare discolouration on the immersed part and on the part exposed to vapour above it, and the change in weight (Canter, 2020). If fresh fluid stays clean and only aged fluid stains, suspect spent inhibitor; if fresh fluid stains too, suspect the formulation itself.

The remedy depends on the coupons. If concentration was low, top up with mix at the recommended strength instead of water to bring it back into range (HSE, 2021). If fresh fluid stained too, ask the supplier for aluminium staining test results and choose a formulation tested on the alloy being machined, all the more for stain-sensitive alloys such as the 7000 series (Canter, 2020). If only aged fluid stained, improve chip removal and filtration to cut what leaves with the chips, and replenish only by the supplier's method. Additives mixed in on the shop floor can clash with other components and cause precipitation or foam (Byers, 2017; Canter, 2020).

Hypothesis 3: poor make-up water

Stains that appear as white spots or small pits, rather than spreading evenly, are a clue that points to the make-up water. This happens in plants that dilute with groundwater or hard water, just after a change of water source, and in sumps that take frequent top-up because evaporation is high. In a sump topped up with tap water all summer to replace what evaporated, small white spots start to appear here and there on aluminium plate. Plate from the next machine, running a fresh mix of the same concentrate, shows none.

With spot stains, chloride ions are the first suspect. Chloride adsorbs at weak points in the oxide film and breaks it locally; as metal dissolves there, the inside of the small hole turns acidic and draws in more chloride. This self-sustaining growth is called pitting (Frankel, 1998), and aluminium is particularly prone to it (Frankel, 1998; Vargel, 2020). Industry reports likewise note that staining risk rises with chloride (Canter, 2020).

Salts also build up in the sump. When water evaporates, the chloride, sulfate, calcium and magnesium dissolved in it stay behind, and every top-up adds more (Byers, 2017; HSE, 2021). Calcium and magnesium, the source of hardness, combine with some inhibitors and precipitate them, so the harder the water, the more of the aluminium's protection drops out of solution (Canter, 2020). Chloride breaks the film directly, while hardness strips the components that cover it, feeding hypothesis 2 as well.

What needs measuring is the water itself. Sample the make-up water and the sump fluid together; read conductivity on a handheld meter, and chloride and total hardness with test kits or outside analysis. A sump value well above the make-up water means build-up from evaporation, while high values in the make-up water itself point to the source. Measuring once at each change of season or water source gives a baseline for later comparison.

When chloride or hardness in the make-up water exceeds the quality the supplier recommends, consider softened or deionised water. Salts already built up in the sump will not fall with top-up alone, so plan a partial or full change (Byers, 2017). Softer water can foam more, so keep an eye on foam after the switch.

Hypothesis 4: parts left wet

When parts that were fine straight after machining and washing stain in storage, look at drying rather than the coolant. It shows up in humid seasons such as the rainy season, when parts from a cold store come into a warm shop, and when parts sit stacked for long spells such as a weekend. Stack aluminium plate finished on a Friday afternoon, separate the sheets on Monday, and the faces that touched carry drop-shaped rims and white marks.

Several things happen at once on a wet surface. Aluminium left in contact with water grows a layer of oxide that holds water, a hydrated oxide, and it grows faster at higher temperature (Hart, 1957). Its thickness and nature differ from the original film, so it shows as white, iridescent or dark stains (Hart, 1957; Vargel, 2020). Where parts are stacked or liquid is trapped in holes and grooves, oxygen cannot get into the gap. The difference in oxygen between inside and outside forms a cell that corrodes the inside further, which is called crevice corrosion (Revie & Uhlig, 2008; Vargel, 2020).

How the liquid dries also shapes the stain. As only the water evaporates from what is left, the liquid grows more concentrated, pH and salts rise locally, and the outline of the dried patch stays behind as a stain (Canter, 2020; Vargel, 2020). This is why rims form along the edges of drops and puddles.

The first check is to separate when the stain forms. Photograph the same part right after machining, after washing and after storage, and see whether stains appear only after storage. Location is a clue too: drop or rim shapes on mating faces, around holes or on the underside most likely come from trapped liquid.

The answer is less time wet. Dry parts with compressed air or blowers straight after machining, do not stack them wet, and tilt parts with many holes and grooves so liquid drains. If parts are washed, check that the cleaner suits aluminium and dry right after rinsing. For long storage, agree a temporary protective oil or packaging suited to aluminium with the supplier (Vargel, 2020).

Hypothesis 5: galvanic corrosion

Sometimes stains gather where another metal touched the part: clamp marks, fixture contact faces, spots where chips sat. This pattern shows up where one sump alternates between steel and aluminium, where steel fixtures and clamps hold aluminium, and where copper-bearing high-strength alloys are machined. One example: after a switch to steel fixtures, grey bands appear along the clamp marks on aluminium brackets, while other faces cut in the same fluid stay clean.

When two different metals touch in a conductive liquid, an electrolyte, the one at lower potential becomes the anode and dissolves, while the one at higher potential becomes the cathode and is protected. This is galvanic corrosion (Revie & Uhlig, 2008; Zhu et al., 2023). Aluminium is the anode when paired with most steels, stainless steels and copper (Zhu et al., 2023), and water-mix coolant, carrying water and salts, is a good electrolyte. That is why local stains and corrosion form near the points where steel fixtures, clamps or steel chips in the sump touch aluminium (Canter, 2020; Zhu et al., 2023).

The same thing happens inside the alloy. In copper-bearing alloys such as the 2000 and 7000 series, small grains where alloying elements such as copper cluster with aluminium, known as intermetallic particles, act as tiny cathodes and dissolve the aluminium around them locally (Birbilis & Buchheit, 2005). This is why one coolant can stain some alloys more than others (Birbilis & Buchheit, 2005; Canter, 2020).

Checking begins with a stain map. Mark on the part whether stains cluster at clamp marks, fixture contact faces or where chips sat, and log how often each alloy stains. Match the work records too: did stains rise after steel was cut in the sump, or start after a fixture change?

Where contact looks responsible, break it. Fit insulating pads at contact faces or use aluminium or plastic fixtures, and clear steel chips from the sump often. Where possible, keep a machine or sump for aluminium only. For copper-rich alloys, run coupon tests on that alloy and dry parts even sooner after machining (Canter, 2020; Zhu et al., 2023).

Testing the hypotheses

Tackling all five hypotheses at once hides which change worked. Check one at a time, starting with what is easy to measure, and narrow the field by when and how the stains appear.

The first step is to sort out when stains form. If they appear only in storage, start with drying and storage under hypothesis 4. If they already show during or right after machining, measure sump pH and concentration and compare them with the supplier's range (HSE, 2021). High concentration with high pH points to hypothesis 1; concentration below the minimum points first to the lean mix of hypothesis 2.

Next come the shape and position of the stains. Even discolouration over faces that sat long in the fluid points to hypothesis 1 or 2, while white spots or small pits point to chloride pitting, hypothesis 3 (Frankel, 1998). Stains clustered where clamps or chips touched suggest hypothesis 5, and rims on mating faces and around holes suggest hypothesis 4 (Revie & Uhlig, 2008; Zhu et al., 2023). If spot stains appear, bring forward the conductivity, chloride and hardness readings on the make-up water and the sump.

If that still does not settle it, run a control test. Half immerse coupons of the same alloy in fresh mix and in sump fluid at the same concentration (Canter, 2020). If both stain, the formulation or its pH does not suit that alloy; if only the sump fluid stains, the cause is spent inhibitor or accumulated salts, and the water readings tell them apart. Where several alloys are machined, include a coupon of each to see how sensitive each alloy is (Birbilis & Buchheit, 2005).

The hypotheses often overlap. Evaporation raises concentration, pH and salts together, and when that fluid is trapped between parts a drying problem is added. In that case correct pH and concentration first, since a reading confirms them at once, then water quality, then drying and contact, changing one thing at a time and watching whether the coupon results change. The job is done only when pH and concentration stay in range over several checks after the fix and the same parts no longer stain.

Limits and cautions

Control ranges for pH and concentration, and water-quality limits, differ by product and alloy, so take targets from the product's technical data and the supplier's recommended range (HSE, 2021). Defects that show after anodising or painting, porosity or segregation in castings, and heat-treatment marks come from material and process, not from the coolant hypotheses, and need to be examined separately. If stains turn into corrosion that affects dimensions or function, or keep returning after the cause has been narrowed, have the fluid and the surface analysed with the supplier's technical staff.

Avoid adding pH adjusters or additives yourself on the shop floor. Coolant mist and skin contact can cause respiratory disease and dermatitis (HSE, 2021; NIOSH, 1998), so check the product's safety data sheet, the SDS, and wear gloves and safety glasses even for measurements and coupon tests.

Sources

  1. Birbilis, N., & Buchheit, R. G. (2005). Electrochemical characteristics of intermetallic phases in aluminum alloys. Journal of The Electrochemical Society, 152(4), B140–B151. https://doi.org/10.1149/1.1869984
  2. Byers, J. P. (Ed.). (2017). Metalworking fluids (3rd ed.). CRC Press. https://www.routledge.com/Metalworking-Fluids/Byers/p/book/9781498722223
  3. Canter, N. (2020, March). Metalworking fluids: Minimizing aluminum staining. Tribology & Lubrication Technology. https://stle.org/files/TLTArchives/2020/03_March/Feature.aspx
  4. Deltombe, E., & Pourbaix, M. (1958). The electrochemical behavior of aluminum: Potential pH diagram of the system Al-H2O at 25 C. Corrosion, 14, 496–500. https://difusion.ulb.ac.be/vufind/Record/ULB-DIPOT:oai:dipot.ulb.ac.be:2013/270827/Details
  5. Frankel, G. S. (1998). Pitting corrosion of metals: A review of the critical factors. Journal of The Electrochemical Society, 145(6), 2186–2198. https://doi.org/10.1149/1.1838615
  6. Hart, R. K. (1957). The formation of films on aluminium immersed in water. Transactions of the Faraday Society, 53, 1020–1027. https://doi.org/10.1039/TF9575301020
  7. Health and Safety Executive [HSE]. (2021). MW5, Managing fluid quality: COSHH essentials for machining with metalworking fluids. https://www.hse.gov.uk/pubns/guidance/mw5.pdf
  8. National Institute for Occupational Safety and Health [NIOSH]. (1998). Criteria for a recommended standard: Occupational exposure to metalworking fluids (DHHS [NIOSH] Publication No. 98-102). https://www.cdc.gov/niosh/docs/98-102/
  9. Revie, R. W., & Uhlig, H. H. (2008). Corrosion and corrosion control: An introduction to corrosion science and engineering (4th ed.). Wiley. https://doi.org/10.1002/9780470277270
  10. Rosalbino, F., Scavino, G., & Ubertalli, G. (2024). Corrosion inhibition of aluminium alloy AA7075-T6 by sodium silicate in chloride solution. Materials Sciences and Applications, 15, 53–65. https://doi.org/10.4236/msa.2024.154005
  11. Vargel, C. (2020). Corrosion of aluminium (2nd ed.). Elsevier. https://shop.elsevier.com/books/corrosion-of-aluminium/vargel/978-0-08-099925-8
  12. Walkner, S., Hafner, M., & Hassel, A. W. (2016). Film dissolution kinetics of aluminium at precisely adjusted pH-values. Physica Status Solidi (a), 213(6), 1410–1416. https://doi.org/10.1002/pssa.201532925
  13. Zhu, Leng, Jin, & Miao. (2023). A review of research on galvanic corrosion of aluminum alloys. Fluid Dynamics & Materials Processing, 19(7). https://doi.org/10.32604/fdmp.2023.025416

Product and site consultation

Leave your company, site and the product groups in use. Our engineer will get in touch to go through your site conditions and concerns. Materials, equipment, operating conditions and downstream steps show what should change and what can stay. If nothing needs to change, we will say so.

Contact us
After you contact us
  1. 01
    Site setup

    We confirm process conditions and needs first.

  2. 02
    Spec design

    We set the product spec and selection criteria.

  3. 03
    Comparison

    We compare matching candidates and propose.

  4. 04
    Tailored supply

    We supply on time and manage the stock.

  5. 05
    Site check

    We visit, check conditions of use and record.

  6. 06
    Use management

    We track use and change cycles to catch issues.

  7. 07
    Regular analysis

    We analyze the records and send a yearly report.