KALTEC

BlogApplication notes

Why are operators getting dermatitis from coolant?

Type
Application notes
Published
20 November 2026
Prepared by
Technical team
Product group
Metalworking Fluids (MWF)

Handing out barrier cream or moisturiser is the usual response when operators' hands break out, but cream cannot stand in for gloves and less exposure. What actually drives the dermatitis can be wet work, strong high-pH fluid, fouled fluid, allergy to additives such as amines and biocides, or cobalt from tools, and irritation and allergy can overlap.

One or two operators on the grinders or lathes start to mention red, cracked skin between their fingers. At first it is put down to dry winter air, but moisturiser does not clear it, and sometimes it spreads to the backs of the hands and the forearms. Others on the same fluid seem fine, and nobody can say why it is that one person, or whether the fluid should be changed.

Dermatitis is one of the health problems most often reported with metalworking fluids. The US National Institute for Occupational Safety and Health, NIOSH, treats skin disease alongside respiratory disease as a main health effect in its criteria document (NIOSH, 1998), and the UK Health and Safety Executive, HSE, states that coolant can cause skin irritation and dermatitis and advises regular checks of hand and forearm skin (HSE, 2024). Operators with dermatitis get moved to other work or take time off, and a missing skilled hand shows directly in machining quality and delivery dates.

The core principle is the skin barrier. The outermost layer of skin, the stratum corneum, keeps water and foreign matter out with its lipids, the skin's own oils, and a mildly acidic surface (Ali & Yosipovitch, 2013). Water-mix coolant is made alkaline to fight rust and bacteria, and it carries surfactants that let oil and water mix, so it works directly against that barrier (OSHA, n.d.). In a study of 286 Dutch metalworkers, most dermatitis was irritant contact dermatitis, in which the skin is damaged directly without an immune reaction, and water-based fluids caused it more often than neat oils, which are used without water (de Boer et al., 1989). The rest was allergic contact dermatitis, an immune reaction to particular ingredients, and that kind returns even when the fluid is well managed (Geier et al., 2004b).

In such cases the technical team sets up the five hypotheses below and rules them out one by one. The start is always the same: watch the affected operator's work for half a shift, counting how often hands touch fluid and get washed, and on the same day measure that machine's concentration and pH against the maker's recommended range and against machines with no cases.

Hypothesis 1: wet work

It shows up in jobs where parts are loaded and unloaded by hand, where tangled chips are cleared by hand, and where wet parts are held for every measurement. It also shows in people who wash often, in people who keep wearing gloves that are wet inside, and in dry workshops in winter. Picture a lathe operator who loads small parts one at a time by hand. Each load and unload wets the hands, tangled chips get pulled out by hand, and every break ends with a hard scrub in abrasive cleanser. All day the backs of the hands are either damp or just dried.

Repeated wetting and drying is what breaks the barrier down. The stratum corneum swells when wet and shrinks when dry, and when that cycle repeats many times a day, the lipid structure between skin cells loosens and the skin lets water and irritants through more and more easily (Behroozy & Keegel, 2014). Dermatology research defines wet work as hands in liquid for more than two hours a shift, occlusive gloves for a similar time, or more than 20 hand washes a shift, and treats it as a main risk factor for hand dermatitis. Some evidence suggests the number of wet-dry cycles matters more than total wet time (Behroozy & Keegel, 2014).

Coolant work meets these conditions easily, and other factors add to them. The US Occupational Safety and Health Administration, OSHA, lists abrasive cleansers, water that is too hot or too cold, winter dryness and fluid-soaked clothing as factors (OSHA, n.d.). An HSE-commissioned study found coolant no more irritating than water over short laboratory contact, and concluded that cutting skin exposure would do more for dermatitis risk than managing concentration, pH, metal fines and bacteria (Semple et al., n.d.).

Watching the work is the first check. Count how many times an hour one operator touches fluid bare-handed, paying most attention to loading, chip clearing and gauging. Note the number of hand washes a day, the cleanser, the water temperature, and whether moisturiser sits at the sink. If dryness, cracks and redness between the fingers and on the backs of the hands stay where the fluid touches, think of irritation first. Where gloves are worn, see whether they stay on wet inside and whether the material suits the fluid.

When the contact and washing counts come out high, the fix lies in cutting the time hands spend wet. Specify chemical-resistant gloves for tasks with no risk of entanglement in rotating parts, and set out in advance which tasks allow gloves and which do not (OSHA, n.d.). Choose gloves on the maker's breakthrough data, and let operators take them off briefly to air sweaty hands, or wear cotton liners (HSE, 2000; HSE, n.d.). Wash with mild cleanser and lukewarm water, and apply moisturiser after work. Barrier cream goes on healthy skin only and replaces neither gloves nor hygiene (OSHA, n.d.), and the evidence that moisturisers prevent dermatitis is of low quality (Bauer et al., 2018). A named person who checks hands and forearms regularly can catch early change (HSE, 2024).

Hypothesis 2: strong, high-pH fluid

It shows up in sumps topped up with concentrate by eye, in summer when a lot of water evaporates, and on machines managed by colour or feel instead of measured concentration. The same goes for the period just after booster is added to correct a low pH. Think of a machining centre where, each time the level drops, an operator brings over the concentrate drum and pours some in by feel. The sump is always full, but the amounts added are written down nowhere, and the refractometer sits in a drawer.

Strong fluid harms skin for the same reason it cleans. The alkaline ingredients in water-mix coolant, such as amines, and its surfactants dissolve the lipids of the stratum corneum just as they dissolve grime on a part. Healthy skin has a mildly acidic surface, and that acidity keeps the barrier-repair enzymes and the skin's resident microbes in balance. Long contact with alkaline fluid raises surface pH, slows barrier repair and meanwhile lets fluid ingredients go deeper (Ali & Yosipovitch, 2013). OSHA likewise lists concentration above the recommended level, and the high alkalinity of in-use fluid that strips natural skin oils, as causes of dermatitis (OSHA, n.d.).

Sump concentration can rise even when nobody adds concentrate, because water evaporates and the concentrate stays behind. Pouring concentrate in by feel can also make it jump at once. As the HSE study shows, though, concentration is a condition that works together with skin exposure, not a cause that produces dermatitis on its own (Semple et al., n.d.).

Checking starts with setting each machine's numbers side by side. Multiply the reading of the refractometer, a handheld meter that reads concentration from one drop, by the maker's correction factor, log it per machine, and compare machines with and without cases. For pH, see whether it sits above the maker's recommended range or has shifted suddenly. Check whether top-up uses neat concentrate or premix and whether the amounts are recorded, and whether concentration and pH are measured on a set schedule.

If the numbers are over range, change how the sump is topped up first. Top up with premix at a set ratio, and measure and adjust concentration and pH often, as OSHA advises (OSHA, n.d.). The ASTM practice on selecting and safely using metal removal fluids likewise treats dilution, top-up and additive control as ways to cut skin hazard (ASTM International, 2023). Bring the affected machine back into range, watch symptoms for some weeks, and if they continue at the right concentration, move on to the next hypothesis.

Hypothesis 3: fouled fluid

It shows up on machines that make a lot of fine swarf, such as grinders, on machines leaking hydraulic or slideway oil, on sumps with no skimmer or a stopped one, and in systems where the fluid has not been changed for a long time. The scene goes like this. A brown film of oil floats on an old grinder sump, and the fluid feels gritty when rubbed between the fingers. A sour smell rises when the pump starts in the morning, and whoever looks after it has been pouring in a dose of biocide each time it smells.

Contamination attacks the skin by two routes. The first is particles. Fine metal pieces and grinding grit in the in-use fluid make invisible cuts when hands wipe or grip a part, and fluid ingredients and metals get in more easily through those breaks. OSHA lists abrasive metal fines, together with tramp oils that leak in from outside the cut, such as hydraulic, gear and slideway oils and grease, as causes of dermatitis (OSHA, n.d.).

The second is microbes. Bacteria and fungi grow in fouled fluid, and NIOSH treats microbial contamination of in-use fluid and its by-products as part of the health risk to workers (NIOSH, 1998). More microbes lead to more biocide, and excess biocide can cause skin irritation or sensitisation (OSHA, n.d.). Contamination is an irritant in itself, and it also raises the allergy risk of hypothesis 4.

The sump surface and the filters are the places to look first. See whether an oil layer floats on top, whether the skimmer runs, whether grit can be felt when the fluid is rubbed between the fingers, and whether there are filter change records. Microbes show as a rotten smell, cloudiness and slime; for a number, test at regular intervals with dipslides, slides coated with growth medium that are dipped in the fluid and incubated to give a bacterial count. Look in the records, too, for who added biocide, when and how much.

Where contamination is visible, removing it and stopping it come first. Skim tramp oil daily and fix leaks at the machine. On high-fines machines such as grinders, review filter grade and change interval. If odour and slime are already present, clean the pipes and sump before refilling rather than only changing the fluid, and keep rubbish and food out of the sump (OSHA, n.d.). Dose biocide only according to measured microbial counts, in set amounts, and record every dose (ASTM International, 2023; OSHA, n.d.).

Hypothesis 4: allergy to additives

Look at this hypothesis when the fluid is well kept and exposure has been cut, but one or two people do not get better. Symptoms that began after a change of product, after a new biocide came in, or after a heavy dose of biocide can take this shape. In one such scene, colleagues on the same line and the same fluid are fine, but one operator's rash climbs past the wrist to the forearms and face. It settles over a holiday and flares again within days of coming back.

Allergic dermatitis needs sensitisation first. In sensitisation, small molecules bind to skin proteins and immune cells learn to recognise the result. Once sensitised, a worker reacts to tiny amounts, so correcting concentration does not cure it, and these ingredients get in more easily through a damaged barrier. That is why allergy can settle on top of long-running irritant dermatitis (de Boer et al., 1989; Geier et al., 2004b).

Studies from a German dermatology network show which ingredients matter. They found the causes by patch testing, in which suspect ingredients are left on the skin to see which provoke a reaction (Geier et al., 2004a, 2004b). In 251 metalworkers tested in 2002 and 2003, monoethanolamine, an alkaline ingredient that prevents rust and holds pH, was positive in 11.6%, the highest of the ingredients still in use (Geier et al., 2004a). Data from 2010 to 2018 still ranked monoethanolamine, colophonium, a rosin from pine resin used as an emulsifier, and formaldehyde-releasing biocides near the top, with the allergens largely unchanged (Schubert et al., 2020).

Start with the way the rash spreads. When it goes beyond the contact areas to the forearms or face, suspect allergy (OSHA, n.d.). Timing comes next: match the dates of a new product, a new biocide or a heavy biocide dose against the date symptoms began. When only one or two of many people on the same fluid are badly affected, individual sensitisation is worth suspecting. Also check the product's safety data sheet, the SDS, for amine, biocide and rosin families.

Refer a worker with suspected allergy to a dermatologist or occupational physician for patch testing. HSE also advises specialist referral and patch testing when skin checks find a problem (HSE, 2024). Once the ingredient is known, ask the supplier for an alternative without it, and log the same worker's symptoms for some weeks after the change. Sensitisation is hard to reverse, so also consider moving a confirmed worker to a post away from that ingredient.

Hypothesis 5: cobalt from tools

This hypothesis applies only where cobalt has a way into the fluid, such as tool rooms that regrind carbide tools and lines that machine carbide or cobalt alloys. In one corner of a tool room, a grinder that resharpens carbide drills and end mills has run on the same sump for a long time without a fluid change. The complaints about sore hands come from the people who run that grinder.

Carbide tools are tungsten carbide grains bound with cobalt. Grinding them drops cobalt-bearing fines into the fluid, and the cobalt then dissolves. A study grinding carbide with nine commercial cutting fluids found that much of the freed cobalt had dissolved within a day, and that final levels in some fluids could harm skin (Einarsson et al., 1979). Dissolved metal does not filter out, so it builds up the longer the fluid is used.

Nickel and chromium also come under suspicion, but the evidence is weak. A study of whether they leach from machined metal into sweat and cutting oil found neither in used oil or wiping rags (Samitz & Katz, 1975). The German data also found cobalt among metalworkers' allergens (Geier et al., 2004b), so when metal allergy is suspected, look at cobalt first.

The questions are what work the site does and who has the symptoms. See whether the site regrinds carbide tools or machines carbide, cobalt alloys, nickel alloys or stainless steel, and whether cases gather among the people on certain grinders or certain materials. If they do, send in-use fluid to an outside laboratory for dissolved cobalt, nickel and chromium, and read the results as a trend rather than a single value.

If cobalt turns up, focus on removing particles before they dissolve. Give carbide grinders a sump of their own and fine filtration so the particles leave before they have time to dissolve. Metal already dissolved does not filter out, so set change intervals from the laboratory results, and ask suppliers about products designed to limit cobalt leaching. Once entanglement risk has been assessed, make gloves the rule on these machines, and review the posts of workers whose patch tests confirm metal allergy.

Testing the hypotheses

Five hypotheses do not need five investigations at once. Rule them out one at a time, starting with what is easy to see and quick to fix.

The starting point is a single table. Put affected operators, their machines, the materials they handle and the dates symptoms began in one table, and it shows whether cases are spread across many machines or gathered on one or two people or one machine. Widespread cases point first to hypotheses 1 to 3, on exposure and fluid control; severe cases in one or two people point first to hypotheses 4 and 5, on allergy.

Next come watching the work and measuring the fluid. If bare-hand contact and hand washes exceed the wet-work definition, cut exposure before hunting for other causes (Behroozy & Keegel, 2014; Semple et al., n.d.). On the same day, compare that machine's concentration and pH with the recommended range and with unaffected machines, and look at tramp oil, filtration, odour, microbial counts and the biocide log together (OSHA, n.d.). This step screens out much of hypotheses 2 and 3.

If that still does not settle it, match times and places. Set the dates of changes in product, biocide, tool or material beside the onset dates, and if cases gather on certain grinders or materials, order a dissolved-metal analysis of the fluid (Einarsson et al., 1979). If symptoms persist for weeks after exposure is cut and the fluid is back in range, or spread beyond the contact areas, the last check is patch testing to find the allergen (HSE, 2024; Schubert et al., 2020).

The hypotheses overlap easily. Strong fluid on long-wet hands gives irritant dermatitis, and biocides or cobalt then enter the damaged skin and sensitise it (de Boer et al., 1989; Geier et al., 2004b). So do not stop at the first cause found; cut exposure and manage the fluid together, and judge the effect by whether symptoms ease.

Limits and cautions

Diagnosis, treatment and confirmation of an allergen belong to a dermatologist or occupational physician. Weeping, cracking, pain or spread beyond the contact areas call for prompt medical care, separately from narrowing the cause on the floor (HSE, 2024). An operator's own atopy, an inborn tendency to sensitive skin, other skin disease and wet exposure at home can also play a part (Behroozy & Keegel, 2014). The figures and findings of each study come from its own conditions and will not fit every site exactly.

Control limits differ by product, so use the maker's recommended range and the SDS as the reference. Wear the protective equipment the SDS names when handling concentrate and biocides, and assess entanglement risk before gloves are used near rotating parts (OSHA, n.d.). Coolant mist and microbial contamination can affect the lungs as well as the skin, so look at exposure control as a whole (NIOSH, 1998).

Sources

  1. Ali, S. M., & Yosipovitch, G. (2013). Skin pH: From basic science to basic skin care. Acta Dermato-Venereologica, 93(3), 261–267. https://doi.org/10.2340/00015555-1531
  2. ASTM International. (2023). ASTM E1497-23, Standard practice for selection and safe use of water-miscible and straight oil metal removal fluids. https://store.astm.org/e1497-23.html
  3. Bauer, A., Rönsch, H., Elsner, P., et al. (2018). Interventions for preventing occupational irritant hand dermatitis. Cochrane Database of Systematic Reviews, 2018(4), CD004414. https://doi.org/10.1002/14651858.CD004414.pub3
  4. Behroozy, A., & Keegel, T. G. (2014). Wet-work exposure: A main risk factor for occupational hand dermatitis. Safety and Health at Work, 5(4), 175–180. https://doi.org/10.1016/j.shaw.2014.08.001
  5. de Boer, E. M., van Ketel, W. G., & Bruynzeel, D. P. (1989). Dermatoses in metal workers. (I) Irritant contact dermatitis. Contact Dermatitis, 20(3), 212–218. https://doi.org/10.1111/j.1600-0536.1989.tb04658.x
  6. Einarsson, O., Eriksson, E., Lindstedt, G., & Wahlberg, J. E. (1979). Dissolution of cobalt from hard metal alloys by cutting fluids. Contact Dermatitis, 5(3), 129–132. https://doi.org/10.1111/j.1600-0536.1979.tb04822.x
  7. Geier, J., Lessmann, H., Dickel, H., et al. (2004a). Patch test results with the metalworking fluid series of the German Contact Dermatitis Research Group (DKG). Contact Dermatitis, 51, 118–130. https://doi.org/10.1111/j.0105-1873.2004.00416.x
  8. Geier, J., Lessmann, H., Schnuch, A., & Uter, W. (2004b). Contact sensitizations in metalworkers with occupational dermatitis exposed to water-based metalworking fluids: Results of the research project "FaSt". International Archives of Occupational and Environmental Health, 77, 543–551. https://doi.org/10.1007/s00420-004-0539-9
  9. Health and Safety Executive [HSE]. (2000). INDG330, Selecting protective gloves for work with chemicals. https://www.hse.gov.uk/pubns/indg330.htm
  10. Health and Safety Executive [HSE]. (2024). Ill health from metalworking and water-mix wash fluids and what to do about it. Updated 2024. https://www.hse.gov.uk/metalworking/waterillhealth.htm
  11. Health and Safety Executive [HSE]. (n.d.). Choosing the right gloves to protect skin: A guide for employers. https://www.hse.gov.uk/skin/employ/gloves.htm
  12. National Institute for Occupational Safety and Health [NIOSH]. (1998). Criteria for a recommended standard: Occupational exposure to metalworking fluids (DHHS [NIOSH] Publication No. 98-102). https://www.cdc.gov/niosh/docs/98-102/
  13. Occupational Safety and Health Administration [OSHA]. (n.d.). Metalworking fluids: Safety and health best practices manual. U.S. Department of Labor. https://www.osha.gov/metalworking-fluids/manual
  14. Samitz, M. H., & Katz, S. A. (1975). Skin hazards from nickel and chromium salts in association with cutting oil operations. Contact Dermatitis, 1(3), 158–160. https://stacks.cdc.gov/view/cdc/184050
  15. Schubert, S., Brans, R., Reich, A., et al. (2020). Contact sensitization in metalworkers: Data from the Information Network of Departments of Dermatology (IVDK), 2010–2018. Contact Dermatitis, 83(6), 487–496. https://doi.org/10.1111/cod.13686
  16. Semple, S., Graham, M., Cowie, H., & Cherrie, J. (n.d.). The causative factors of dermatitis among workers exposed to metalworking fluids (HSE Research Report RR577). Health and Safety Executive. Publication year not confirmed. https://www.hse.gov.uk/research/rrhtm/rr577.htm

Product and site consultation

Leave your company, site and the product groups in use. Our engineer will get in touch to go through your site conditions and concerns. Materials, equipment, operating conditions and downstream steps show what should change and what can stay. If nothing needs to change, we will say so.

Contact us
After you contact us
  1. 01
    Site setup

    We confirm process conditions and needs first.

  2. 02
    Spec design

    We set the product spec and selection criteria.

  3. 03
    Comparison

    We compare matching candidates and propose.

  4. 04
    Tailored supply

    We supply on time and manage the stock.

  5. 05
    Site check

    We visit, check conditions of use and record.

  6. 06
    Use management

    We track use and change cycles to catch issues.

  7. 07
    Regular analysis

    We analyze the records and send a yearly report.