BlogApplication notes
Why are machine tables and slideways rusting?
- Type
- Application notes
- Published
- 20 November 2026
- Prepared by
- Technical team
- Product group
- Metalworking Fluids (MWF)
Raising tank concentration is the usual response to rust on a machine, but even with the tank in range, the film left on the surface can be in a different state. What actually brings rust can be a film short of inhibitor, tramp oil that got in, condensation during shutdowns, liquid trapped in gaps or salt left as the film dries, and often two of these at once.
Open the guard after a weekend and the table may be spread with faint brown stains; lift a vise that stayed clamped for a long time and rust is printed in the shape of its base. Wiping it off does not help for long: within days it is back in the same place, yet the tank concentration reads fine. When rust keeps coming back on the machine surface while the tank concentration is in range, look at the film left on that surface and at its surroundings.
Tables and slideways are the reference surfaces of a machine. Rust roughens them, rust particles caught between sliding faces speed up wear, and an uneven seat for the workpiece costs accuracy. Grinding the rust away removes part of the reference surface itself, so rust once formed is a loss that is hard to undo.
Iron rusts when a water film sits on it and oxygen reaches that film. Iron dissolves into the film as ions, particles carrying an electric charge, and the freed electrons are used where oxygen meets water to form hydroxide ions. The two meet to form iron hydroxide and then rust (Brinksmeier et al., 2015; Vernon, 1935). Water-mix coolants slow this with a mildly alkaline pH and corrosion inhibitors. The inhibitors cling to the metal surface and form a thin protective layer, and how much is present depends on the working concentration (Brinksmeier et al., 2015; Byers, 2018). Rust therefore forms where a film short of inhibitor, or plain water with none, stays on the metal. The checks that the UK Health and Safety Executive and the US National Institute for Occupational Safety and Health recommend for coolant, covering concentration, pH, tramp oil and microbes, exist to protect health (HSE, 2021; NIOSH, 1998), but they overlap almost entirely with the conditions that prevent machine rust.
In such cases the technical team sets up the five hypotheses below and rules them out one by one. The start is always the same: record the date and place where rust first appeared, compare tank concentration and pH with the supplier's recommended range on the same day, and look at whether the film at the rust spot is tacky, oily or carrying white residue.
Hypothesis 1: inhibitor shortfall
This hypothesis comes to mind first when tank concentration sits at the low end of the recommended range, when the sump has been topped up with water alone, and on jobs that make a lot of chips, cast iron above all. Think of a machining centre cutting cast iron housings, where wet chips and sludge are left on the table at the end of the shift. Next day, when the chips are swept away, rust follows the places where they lay, and small dots of rust are scattered over the broad areas where mist settled.
During cutting, coolant becomes mist and droplets that settle thinly on tables, inside guards and at slideway ends (NIOSH, 1998). A thin film has a large contact area with air for its volume, so oxygen reaches the metal easily, and its make-up keeps changing as the water leaves first. Inhibitor content scales with working concentration (Byers, 2018), so when the tank has gone lean, the film keeps correspondingly less inhibitor. Chips consume inhibitor too. Freshly cut chips have a very large surface for their mass, and inhibitor adsorbs onto it and leaves the fluid. Tests on a synthetic fluid measured and modelled how fast inhibitor is lost by adsorption onto freshly cut chips (Eppert et al., 2003). Cast iron chips have graphite touching iron, so the two act like a tiny battery and the iron dissolves in its place (Revie & Uhlig, 2008). The ground under cast iron chips and sludge on a table therefore easily becomes a wet spot stripped of inhibitor.
The shape of the rust is the first clue. Dots spread evenly over the broad areas mist reaches, with rust following the outline of chips where they lay, point this way. Read tank concentration on a refractometer to see whether it sits at the low end of the range; tramp oil can push the reading up, so test a sample with the oil layer removed (HSE, 2021). Inhibitor margin can be compared with the ASTM D4627 iron chip test, in which grey cast iron chips wetted with the fluid sit on filter paper and the lowest concentration that leaves no rust stain is found (ASTM International, 2022).
If concentration is low, top up with diluted coolant rather than water to bring it back into range (HSE, 2021). Clear chips and sludge off the table at the end of each shift, and before stopping, rinse once with clean working fluid so that an inhibited film remains. If the chip test stains even at the recommended concentration, the inhibitor performance itself has dropped, so decide on a recharge or a product review with the supplier.
Hypothesis 2: tramp oil ingress
When rust forms in lines at slideway ends and around the wipers, tramp oil is the first place to look. That means machines with leaking hydraulic lines, machines whose slideway lubrication has crept up, and machines where coolant splashes heavily onto the ways. A lathe whose way oil reservoir now needs filling more often than before is one example. Streaks of rust run along the slideway ends, a brown oil layer floats on the coolant tank, and after a holiday a rotten-egg smell rises from the sump.
Way oil and hydraulic oil escape from slideways and hydraulics into the coolant tank. Oil mixed in this way is called tramp oil, and a production study found continuous hydraulic oil ingress to be a major variable that unsettles fluid performance (Khan et al., 2021). Part of the oil is emulsified into the coolant and part floats as a layer. Some emulsifier and inhibitor migrates into that oil, shrinking the fluid's rust margin (Brinksmeier et al., 2015; Byers, 2018). The floating layer cuts off oxygen at the tank surface, favouring anaerobic bacteria that grow without oxygen, and the oil itself is food for microbes. The microbes break down inhibitors and release organic acids that lower the pH, weakening the rust protection of the whole fluid (Passman & Küenzi, 2020; Saha & Donofrio, 2012). Seen from the slideway side, the same exchange works like this: coolant splashed on the ways emulsifies the way oil and washes it off, and the oil it carries away reaches the tank as tramp oil. The way, stripped of its oil film, is left as bare iron in contact with water.
Check whether an oil layer on the tank, a rotten-egg smell after shutdowns and higher-than-usual way oil consumption appear together. See also whether rust forms in streaks at slideway ends, around the wipers and where the oil film on the way breaks. Stand a sample in a graduated cylinder for a day to read how much oil floats, and check pH and microbes with a dipslide at the same time (HSE, 2021).
If tramp oil looks like the cause, remove the floating oil regularly with a skimmer or centrifuge (HSE, 2021). If way oil use has risen, check the lubrication setting and the hydraulic lines for leaks first, because unless the way in is closed, skimming only grows. Use a way oil that separates well from coolant, and if microbe counts are high or pH keeps falling, consider cleaning and recharging (Passman & Küenzi, 2020).
Hypothesis 3: shutdown condensation
Condensation gives itself away by its timing: rust that clusters on Monday mornings or after holidays. It appears first on machines with heavy cast iron tables and beds, on machines near doors and vents, and on machines along walls that face the outside air. On a Monday morning in the rainy season the shutters go up and warm, damp outside air rolls into the plant, yet a table that sat cooling all weekend is still cold to the touch. By lunchtime an even, thin brown film lies across the whole table.
Condensation comes from the temperature gap between air and metal. Water vapour in the air condenses when a surface falls below the dew point. The dew point is calculated from air temperature and relative humidity, and the standard for preparing steel before painting judges condensation risk by comparing surface temperature with dew point, usually requiring the surface to be at least 3°C above it. The same standard notes that thin condensed films on steel are mostly invisible (ISO, 2017). Heavy cast iron tables and beds hold a lot of heat and so warm more slowly than the air. When they cool overnight or over a weekend and then the heating comes on and doors open in the morning, warm, humid air meets still-cold metal and condenses easily. That water film carries no inhibitor, and where the salts of hypothesis 5 remain, rust advances faster (ISO, 2012; Schindelholz et al., 2015). The atmospheric corrosivity standard likewise treats the time a surface stays wet as a key factor (ISO, 2012).
Begin by logging the timing. If rust clusters after shutdowns and appears as an even, thin brown film over the whole table, this hypothesis is the strong one. During shutdowns, log air temperature, humidity and table surface temperature together, and look for periods when the surface comes within 3°C of the dew point; those periods carry a high condensation risk (ISO, 2017). Within the same plant, compare whether rust starts first on machines near doors and outside walls.
For machines that stand idle for a weekend or holiday, wipe the tables and slideways, apply a thin coat of rust preventive and cover them where possible. At restart, raise the indoor temperature gradually before opening doors, or warm the machines before letting outside air in. Circulating the coolant periodically during shutdowns keeps oxygen in the tank and also limits the odour and pH drop at restart (HSE, 2021; Passman & Küenzi, 2020).
Hypothesis 4: trapped liquid
This hypothesis covers rust that grows only in particular places: under vises and fixtures, inside T-slots, and beneath the paint on the machine body. It concerns production lines where fixtures stay clamped for long periods, machines whose T-slots fill with chips, and painted surfaces that chips often scratch or cleaners keep wet. Suppose a vise clamped in the same place for months is released and lifted for the first time on a maintenance day. The table carries rust printed in the exact shape of the vise base, and rust lines the inside of the T-slots too.
Inside a gap, the shortage of oxygen actually speeds rust up. When coolant seeps into the narrow gap under a vise or fixture and is trapped, the liquid there uses up its oxygen, gets no fresh supply, and comes to differ from the oxygen-rich liquid outside. Iron then dissolves inside the oxygen-poor gap, which is called crevice corrosion. The trapped liquid grows more acidic, so the attack sustains itself (Revie & Uhlig, 2008). The paint on the machine body forms the same kind of gap. When chips scratch it, or it swells after long soaking in cleaners and coolant, liquid gets underneath. On painted steel, corrosion that starts this way spreads like threads between paint and metal, which is called filiform corrosion, and iron dissolving beneath the paint lifts it (Cristoforetti et al., 2024). That is why rust that looks like a small spot on top may have spread widely beneath.
Lifting and pressing are how this is checked. Lift the vise or fixture and see whether rust is printed in the outline of its base, and whether rust lines the inside of the T-slots. On painted surfaces, look for blistering or brown liquid weeping out and for rust starting at scratches, edges and around bolts; if the paint lifts easily under a fingernail or tape, treat the rust as having spread beneath already. If the cleaner was changed recently or the coolant concentration raised, check whether the paint stands up to that liquid by keeping a small area wet with it.
Release long-standing vises and fixtures regularly to clean and oil their bases and the table, and empty chips from the T-slots every shift. Strip lifted paint back to where the rust ends, remove the rust and repaint, because painting over lifted paint lets the rust beneath keep growing. Shield spots that chips hit often with covers or guard plates to limit paint damage, and when changing coolant or cleaner, confirm with the supplier that it suits the machine's paint.
Hypothesis 5: dried salt residue
Suspect salt when white powder or hard crystals ring the rust. It shows in plants that top up with water high in hardness or chloride, in tanks that have gone through evaporation and top-up for a long time, and in summer and in grinding, where a lot of water evaporates. White powder has dried onto the edge of a grinder table, with rust spreading round it. Wipe it off with a rag and a few days later it is back in the same place.
Coolant is mostly water. When water evaporates from a film on the machine, the chloride, sulfate and hardness salts it carried do not leave with it; they stay on the surface and concentrate. The same happens in a tank that is repeatedly evaporated and topped up, so salt levels rise over time (Byers, 2018; HSE, 2021). Chloride is the classic ion that breaks down the protective layer on iron locally and starts pit-like corrosion (Revie & Uhlig, 2008). Leftover salt also draws moisture from the air. In tests on steel carrying magnesium chloride and artificial sea salt, corrosion continued for up to 30 days at 11 to 23% relative humidity, below the humidity at which the salt takes up water and turns liquid, about 33% for magnesium chloride (Schindelholz et al., 2015). The thin water held around the salt crystals acts as a conducting liquid, an electrolyte. This follows the principle that atmospheric corrosion depends on the time of wetness during which a film stays on the surface (ISO, 2012; Vernon, 1935). A spot carrying white residue can therefore keep rusting even when the plant looks dry.
Measuring the water gives the answer. Measure the conductivity, chloride and hardness of both the make-up water and the working fluid; values in the fluid that keep rising above those at first charge mean salts are concentrating (HSE, 2021). Note as well whether white powder or crystals stay around the rust, whether it returns to the same spot after wiping, and whether it appears sooner in summer and on grinding.
If the make-up water is high in chloride and hardness, consider purified water such as softened or reverse-osmosis water (Byers, 2018). Do not rub dried residue with a dry rag; dissolve it with working fluid or an inhibited cleaner and then wipe it off, because rubbing it dry leaves the salt behind and only scratches the surface. If the fluid's conductivity has risen well above its starting value and will not come down, top-up cannot reduce the salts, so bring the recharge forward.
Testing the hypotheses
Separating the five hypotheses does not call for analytical equipment at the outset. Recording exactly when and where rust appeared already narrows the field a great deal. If rust clusters on Monday mornings or after holidays, look first at condensation, hypothesis 3.
Location says even more. Dots scattered over broad areas the mist reaches point to hypothesis 1; streaks at slideway ends and around the wipers, to hypothesis 2; fixed places such as under vises and fixtures, in T-slots or on paint, to hypothesis 4; spots carrying white residue, to hypothesis 5. Touching the film at the rust spot to feel whether it is tacky, oily or powdery helps the same judgement.
Next come the fluid's numbers, measured on the same day. Low concentration means hypothesis 1, and a falling pH points to microbes and tramp oil, hypothesis 2 (HSE, 2021). A thick oil layer on the tank and a smell after shutdowns make hypothesis 2 firmer still. Conductivity and chloride in the working fluid rising steadily above their starting values mean hypothesis 5 (HSE, 2021).
If the numbers do not settle it, run the chip test as a control. Test the in-use fluid side by side with fresh fluid made from the same concentrate at the recommended concentration; if only the in-use fluid leaves rust stains, the fluid itself has lost protection (ASTM International, 2022). The final check is to clean the rust spot, apply the fix and see that rust does not return to the same place after the next shutdown.
The hypotheses often overlap: condensation forms on a salt-laden surface, or tramp oil feeds microbes so that pH and protection fall together. When they overlap, put right the problems in the fluid itself, hypotheses 1, 2 and 5, first, then deal with the surface and the surroundings, hypotheses 3 and 4. If the fluid is poor, surface care does not last.
Limits and cautions
For numeric limits such as concentration and pH, the maker's recommended range for the product in use comes first. Discolouration of stainless, aluminium or copper-alloy parts, stray-current corrosion caused by leaking electrical current, and coastal sites with salty air follow other mechanisms and are not judged by the five hypotheses above. Where rust on precision slideways is deep or widespread, consult the machine builder about grinding or rework.
When handling rust removers, cleaners and rust preventives, check the product's safety data sheet, the SDS, and wear protective gloves and eye protection. Coolant mist and skin contact can cause respiratory and skin disease, so measures that cut mist serve rust prevention and health at the same time (HSE, 2021; NIOSH, 1998).
Sources
- ASTM International. (2022). ASTM D4627-22, Standard test method for iron chip corrosion for water-miscible metalworking fluids. https://store.astm.org/d4627-22.html
- Brinksmeier, E., Meyer, D., Huesmann-Cordes, A. G., & Herrmann, C. (2015). Metalworking fluids: Mechanisms and performance. CIRP Annals, 64(2), 605–628. https://doi.org/10.1016/j.cirp.2015.05.003
- Byers, J. P. (Ed.). (2018). Metalworking fluids (3rd ed.). CRC Press. Includes the chapter "Corrosion: Causes and cures" by G. J. P. Becket. https://www.routledge.com/Metalworking-Fluids/Byers/p/book/9781498722223
- Cristoforetti, A., et al. (2024). Recent progress in understanding filiform corrosion on organic coated steel: A comprehensive review. Progress in Organic Coatings, 192, 108469. https://iris.unitn.it/retrieve/2c3795ee-8e42-46ac-a3df-ff1c8a8dafc1/1-s2.0-S0300944024002613-main%20POC%20Cristoforetti%20REV%20com.pdf
- Eppert, J., DeVor, R. E., Kapoor, S. G., & Rajagopalan, N. (2003). The effect of chip adsorption on selective depletion from a multicomponent synthetic metalworking fluid. University of Illinois at Urbana-Champaign, IDEALS. https://www.ideals.illinois.edu/items/110202
- Health and Safety Executive [HSE]. (2021). MW5, Managing fluid quality: COSHH essentials for machining with metalworking fluids. https://www.hse.gov.uk/pubns/guidance/mw5.pdf
- International Organization for Standardization [ISO]. (2012). ISO 9223:2012, Corrosion of metals and alloys: Corrosivity of atmospheres: Classification, determination and estimation. https://www.iso.org/standard/53499.html
- International Organization for Standardization [ISO]. (2017). ISO 8502-4:2017, Preparation of steel substrates before application of paints and related products: Tests for the assessment of surface cleanliness: Part 4: Guidance on the estimation of the probability of condensation prior to paint application. https://www.iso.org/standard/58061.html
- Khan, T., Broderick, M., & Taylor, C. M. (2021). Investigating the industrial impact of hydraulic oil contamination on tool wear during machining and the development of a novel quantification methodology. The International Journal of Advanced Manufacturing Technology, 112(1–2), 589–600. https://doi.org/10.1007/s00170-020-06370-y
- National Institute for Occupational Safety and Health [NIOSH]. (1998). Criteria for a recommended standard: Occupational exposure to metalworking fluids (DHHS [NIOSH] Publication No. 98-102). https://www.cdc.gov/niosh/docs/98-102/
- Passman, F. J., & Küenzi, P. (2020). Microbiology in water-miscible metalworking fluids. Tribology Transactions, 63(6), 1147–1171. https://doi.org/10.1080/10402004.2020.1764684
- Revie, R. W., & Uhlig, H. H. (2008). Corrosion and corrosion control: An introduction to corrosion science and engineering (4th ed.). Wiley. https://doi.org/10.1002/9780470277270
- Saha, R., & Donofrio, R. S. (2012). The microbiology of metalworking fluids. Applied Microbiology and Biotechnology, 94, 1119–1130. https://doi.org/10.1007/s00253-012-4055-7
- Schindelholz, E., Risteen, B., & Kelly, R. G. (2015). Impact of salt deliquescence on the humidity-dependence of atmospheric corrosion [Conference abstract]. 228th Meeting of The Electrochemical Society. https://ecs.confex.com/ecs/228/webprogram/Paper61196.html
- Vernon, W. H. J. (1935). A laboratory study of the atmospheric corrosion of metals. Part II: Iron: The primary oxide film. Part III: The secondary product or rust. Transactions of the Faraday Society, 31, 1668–1700. https://doi.org/10.1039/TF9353101668