BlogApplication notes
Why is tool life short even at the right concentration?
- Type
- Application notes
- Published
- 20 November 2026
- Prepared by
- Technical team
- Product group
- Metalworking Fluids (MWF)
When the refractometer reads inside the recommended range, it is easy to assume the coolant is doing its job, but that number does not show whether lubrication and cooling actually happen at the edge. What actually shortens tool life can be an overstated reading, weak lubricity, coolant delivery that does not suit the cut, chips and fines that are not cleared, or a changed material, and sometimes two of these at once.
Sometimes the refractometer reading lands inside the recommended range every time, yet tools need changing sooner than before. The programme and the tool are unchanged, but inserts are swapped more often, and by the end of a shift dimensions wander or the surface turns rough. On the concentration log the fluid seems to be doing its job, so it is hard to know where to look.
Tools are an obvious consumable, but the loss does not stop at the tool bill. Short tool life also brings more stops for tool changes, more dimensional scrap and more surface defects. And tool life is set jointly by the material, the tool, the cutting conditions and the machine, not by the fluid alone, so no single number can settle the cause (Liao et al., 2024).
A water-mix coolant does three jobs in the cut. It draws heat away from the edge, reduces friction and adhesion between tool and chip, and flushes chips out of the cutting zone (Brinksmeier et al., 2015; Yan et al., 2016). If any one of these weakens, wear speeds up. A hotter edge softens the tool material and speeds diffusion wear, in which tool elements dissolve into the chip. Poor lubrication lets workpiece metal stick to the edge and tear small pieces away when it breaks off (Trent & Wright, 2000). The refractometer number gives a rough idea of how much is in the fluid; it does not show whether those three jobs happen at the edge.
In such cases the technical team sets up the five hypotheses below and rules them out one by one. The start is always the same: take circulating fluid near the nozzle, measure it again on a calibrated refractometer, and on the same day log the tramp oil level and the wear pattern on a worn tool. These three side by side, not one number, are what narrow the hypotheses.
Hypothesis 1: overstated reading
It tends to happen on older machines that weep hydraulic or slideway oil, in shops that zeroed the refractometer once when it arrived and never again, and where the habit is to sample straight off the top of the sump. Think of a row of machining centres. Each shift an operator lifts the sump lid, draws fluid from the surface with a pipette and puts it on the refractometer, and the log always shows a value inside the range. Yet the end mills on that line keep turning up early on the change list.
The first reason the number and reality part ways lies in how it is measured. A refractometer measures how strongly the liquid bends light, and that value is multiplied by the refractometer factor, a conversion number set for each product, to give concentration. The method sees everything dissolved or mixed in the water. So when tramp oil leaking from the machine gets in, the scale becomes hard to read, and analogue units lose accuracy in particular. Calibrating only once, or using a unit without temperature compensation, adds more error (Canter, 2011).
The deeper reason is that components deplete at different rates. Once diluted, emulsifiers, lubricity additives and corrosion inhibitors leave on chips or break down at their own pace, so the refractometer can hold steady while only the lubricating part has fallen (Canter, 2011). Tramp oil also changes lubrication by itself: in one study, tool life varied by up to 70% as tramp oil built up in the system (Khan et al., 2021). The same number can hide quite different conditions at the edge.
Look first at the line on the refractometer. A blurred or fuzzy line is a sign of heavy tramp oil or contamination, so let a sample stand and see whether an oil layer rises (Canter, 2011). Guidance advises keeping tramp oil below 2% and checking it weekly (HSE, 2021). Take the sample from circulating fluid near the nozzle, not from the top of the sump (Canter, 2011). Then add an alkalinity titration, which adds reagent drop by drop until the colour changes and reads concentration from the amount used, or an acid split, and see whether the result drifts from the refractometer (Canter, 2011).
If the two values drift apart or tramp oil is over the guide, put the measurement right first. Zero the refractometer with clean water before every reading and apply the manufacturer's refractometer factor. Skim tramp oil continuously with a skimmer or coalescer, and find and fix the leaks (HSE, 2021). Since evaporation concentrates the sump, top up with a mix weaker than the recommended concentration (HSE, 2021). If the reading is right but tool life stays short, cross-check by titration on a regular schedule.
Hypothesis 2: weak lubricity
Look at this hypothesis when the measurement checks out yet workpiece metal still welds to the edge. It tends to show when the shop moves to hard-to-cut alloys or heavier cuts, when lubrication-heavy work such as tapping, reaming, broaching or deep-hole drilling grows, or when one general-purpose fluid has to serve every material. Take a line that cuts carbon steel parts and now gets a job in the same steel with many tapped holes. The fluid and its concentration are unchanged, yet taps last only a handful of holes and the threads come out torn and rough.
At the edge, pressure and temperature are so high that the oil film cannot hold. Metal meets metal there, a state called boundary lubrication, and what protects the surfaces is the extreme-pressure additive, or EP additive (Li et al., 2022). In a water-mix coolant, lubrication comes from the base oil, the emulsifiers and the lubricity and EP additives together, and their type and ratio differ by product, so lubricating performance can differ widely at the same concentration (Bassetti et al., 2024). The right concentration means the set amount went in, not that the amount can stand up to this material and this cut.
EP additives carrying sulfur, phosphorus or chlorine react with the metal under frictional heat and form thin films such as sulfides, phosphates and chlorides. These films shear away first and keep tool and workpiece from welding together (Li et al., 2022). In milling tests on high-strength steel, a highly reactive sulfur additive, a polysulfide, cut specific cutting energy and tool wear the most, and reactivity tracked performance (Bierla et al., 2012). Conversely, a fluid weak in these components, used on hard-to-cut alloys or heavy cuts, lets workpiece metal weld and pile up on the edge as a built-up edge, and when that lump breaks off it takes part of the edge with it (Trent & Wright, 2000).
The first check is a loupe on the worn edge. A built-up edge or marks of welded workpiece metal point to lubrication before anything else (Trent & Wright, 2000). Compare surface roughness and spindle load with earlier records at the same settings. If tool life fell just when a new material or lubrication-heavy work arrived, the hypothesis gains weight.
The first move is to raise concentration toward the top of the manufacturer's recommended range. If nothing changes, the issue is not the dose but a lubricity design that does not suit the job, so trial a fluid with EP chemistry suited to the material and operation, side by side on the same tool and settings. Only a trial that runs several tools to the same end criterion, compared by parts made or flank wear, gives a clear answer.
Hypothesis 3: wrong coolant delivery
This hypothesis comes up on machines where the nozzle was not re-aimed after a tool change, on systems where a clogged filter has cut flow, and in deep turning or drilling where the chip covers the edge. There is an opposite case too: flooding an interrupted cut such as milling, where the edge enters and leaves the work again and again. Say a longer tool went in, and since then the coolant stream has been hitting the chips above the edge rather than the edge itself, with nobody looking that way. On the next machine, every milling insert that comes out carries several fine cracks across its edge.
Most cutting heat forms in the small zone where tool and chip meet. The chip covers that zone and keeps fluid out, so how deep the fluid gets decides how well it cools and lubricates (Yan et al., 2016). If the nozzle is off the edge or flow is short, fluid runs over the chip only, and the edge is close to dry whatever the sump concentration. Pushing fluid under the chip with pressure can change the result sharply. In turning nickel-base alloy 718 with coated carbide, a 203 bar supply raised tool life by up to 740% over conventional flood, which the authors put down to the jet lifting the chip and getting fluid closer to the cutting zone (Ezugwu & Bonney, 2004). That figure belongs to that alloy and those conditions.
In interrupted cuts the risk lies the other way. The edge heats up as it enters the work and is quenched by fluid as it leaves, over and over, and thermal cracks and chipping follow. In milling precipitation-hardened stainless steel with carbide inserts, dry cutting gave longer tool life than abundant emulsion, and thermal cracks and chipping appeared with emulsion whatever the delivery method or concentration (Diniz et al., 2008).
The edge itself tells which side applies. A discoloured or rounded edge is a sign of heat left behind, so check that the nozzle points at the edge and was not knocked off line at the last tool change. Several comb-like fine cracks across the edge of a milling insert point to thermal shock (Diniz et al., 2008). Log whether a clogged filter or nozzle has cut flow and whether pump pressure is at its usual level.
If turning or drilling shows heat wear, aim the nozzle at the edge and under the chip, and where possible trial through-tool coolant or higher pressure (Ezugwu & Bonney, 2004). Thermal cracks in milling call for the opposite: for that material and tool, trial dry cutting, air blast and minimum-quantity lubrication, or MQL, which carries a tiny amount of oil on air (Debnath et al., 2014; Diniz et al., 2008). Either way, compare the life of several tools to the same criterion after the change.
Hypothesis 4: recut chips and fines
This hypothesis belongs to cuts where chips have a narrow way out, such as deep pockets, narrow slots and deep holes, and to sumps whose filtration is undersized or neglected. A deep pocket in a mould block is a good scene. The end mill is fine on the shallow steps, but near the pocket floor its edge starts to chip in places, and a scraper run along the sump bottom brings up a grey, mud-like deposit.
Chips that linger in the cutting zone catch the edge again. When the edge recuts a chip that is already work-hardened, or a chip strikes the edge, small pieces break from the edge and wear suddenly speeds up. The test in which high-pressure coolant lifted the chip and extended tool life also shows how closely chip flow is tied to tool life (Ezugwu & Bonney, 2004).
Fines you cannot see harm the edge too. Machining makes millimetre-scale chips along with very fine metal particles, and unfiltered fines pass through the pump back into the cutting zone. There they can get caught between tool and workpiece and scratch the edge and the surface like grinding grit (Khan et al., 2021). Fines also bind with tramp oil into sludge, a mud-like deposit on the sump bottom (HSE, 2021; Khan et al., 2021).
Suspect recutting when the edge breaks irregularly instead of wearing evenly, or shows dents pressed in by chips. Compare whether the same tool is fine in shallow cuts and fails fast only in deep pockets or holes. A sample left in a clear bottle shows whether metal fines settle, and the filter pressure drop and change interval are worth checking alongside.
Chip clearance starts with the nozzle. Where chips linger, turn it toward the way out, raise pressure or flow, or use through-tool coolant (Ezugwu & Bonney, 2004). In drilling, adjust the peck cycle, in which the drill backs out in steps to break and clear chips. Remove fines with centrifuges, filters or magnetic separators, and check filters on a schedule (HSE, 2021). If fines and sludge have already built up heavily, it is faster to drain, clean the system and refill.
Hypothesis 5: changed material
If neither the fluid nor its delivery has changed but tool life fell from one day on, look at the material. Typical cases are a new supplier, a lot of the same grade in a different heat-treated condition, or new work in materials such as nickel alloys, titanium alloys or austenitic stainless steel. Imagine the week after purchasing switched bar supplier to save cost. The drawing and the grade on it are the same, yet inserts run on the same programme come out with a groove worn at one spot on the edge.
Tool life depends heavily on the material's machinability, how readily it cuts. Machinability is not a single number; it comes from how hardness, microstructure and thermal properties act together on tool wear, cutting force, temperature and chip form (Liao et al., 2024). Even within one grade, a different heat treatment or supplier changes hardness and structure, and with them the edge temperature and wear rate at the same settings (Trent & Wright, 2000).
Materials that hold heat make it worse. Nickel and titanium alloys conduct heat poorly, so heat cannot escape into the chip and workpiece and gathers at the edge, which drives fast wear (Ezugwu, 2005). In strongly work-hardening materials such as austenitic stainless steel, the surface left by one pass hardens, and the next pass through that layer tends to notch the edge at the depth-of-cut line (Trent & Wright, 2000). With such materials, cutting conditions and tooling need setting before the fluid.
The clue comes from lining up records. Set the date tool life fell beside material receipt records and beside the hardness and heat treatment on the mill certificate, the composition and property report the steel maker issues with each lot. A notch worn like a groove at one spot on the edge points to a work-hardened layer or surface scale (Trent & Wright, 2000). Test the hardness of the suspect material and compare it with the previous lot.
If the material has indeed changed, reset speed and feed from the tool maker's recommendations for that material, and change tool grade or coating if needed. For strongly work-hardening materials, do not set feed and depth of cut so light that the edge rubs in the hardened layer instead of cutting beneath it. If life is still short after that, go back to the lubrication and cooling hypotheses above.
Testing the hypotheses
Work through the five hypotheses starting with the checks that cost least and answer fastest. Tool life is set by several factors at once (Liao et al., 2024), so looking at one at a time is actually the shortest way.
The first step is to line up dates. Set the date tool life fell beside material lots, tool lots, programme changes and fluid top-up and change records. A match with a new material lot or supplier leans toward hypothesis 5, a match with new lubrication-heavy work such as tapping or reaming toward hypothesis 2, and a match with a tool change or nozzle work toward hypothesis 3. Then measure a near-nozzle sample on a calibrated refractometer and compare it with titration, to be sure the reading itself can be trusted. If tramp oil is above 2% or the two values drift apart, settle hypothesis 1 first (Canter, 2011; HSE, 2021).
The next clue is the edge. Welded workpiece metal points first to hypothesis 2, a discoloured, rounded edge to heat under hypothesis 3, comb-like cracks to thermal shock under hypothesis 3, irregular breakage to hypothesis 4, and a notch at the depth-of-cut line to hypothesis 5 (Diniz et al., 2008; Trent & Wright, 2000). If life is short only in deep work, look at chip clearance; if the same tool wears differently from machine to machine, compare nozzle aim, flow, pressure and filter condition machine by machine.
If that still does not settle it, move on to a control trial. Change only one of concentration, delivery, cutting conditions or product, hold the rest, and run several tools to the same wear criterion, comparing parts made. Change two at once and there is no telling which one worked. The last check is whether tool life returns to its earlier recorded level over several tool changes after the fix.
The hypotheses can overlap. A sump heavy with tramp oil clouds the reading, changes lubrication (Canter, 2011; Khan et al., 2021) and binds with fines into sludge as well. When adhesion and heat wear appear together, fix the delivery first and then look at lubricity, because no product can perform if it never reaches the edge.
Limits and cautions
Recommended concentrations and control ranges differ by product, so follow the product data sheet and the supplier's range. Tool life is set jointly by the material, the tool, the conditions and the machine (Liao et al., 2024), so causes on the machine and tool side, such as tool grade or geometry defects, machine vibration, spindle condition and tool paths, need their own look. The figures cited come from the materials and conditions of those studies and do not transfer directly to another shop (Diniz et al., 2008; Ezugwu & Bonney, 2004). Interpret tool-life trials and decide on product changes together with the technical staff of the fluid and tool suppliers.
Raising pressure and flow raises mist. The US National Institute for Occupational Safety and Health set a recommended exposure limit for metalworking fluid aerosols of 0.4 mg/m³ as thoracic particulate and 0.5 mg/m³ as total particulate, based mainly on respiratory disease (NIOSH, 1998). When changing delivery, check machine enclosures and local exhaust as well. Before raising concentration or adding additives, read the product's safety data sheet, the SDS, and wear gloves and safety glasses to limit skin contact (HSE, 2021; NIOSH, 1998).
Sources
- Bassetti, J., Poulesquen, A., & Pierlot, C. (2024). Review on cutting fluids: Formulation, chemistry and deformulation. Journal of Oleo Science, 73(7), 921–941. https://doi.org/10.5650/jos.ess24068
- Bierla, A., Fromentin, G., Minfray, C., Martin, J.-M., Le Mogne, T., & Genet, N. (2012). Mechanical and physico-chemical study of sulfur additives effect in milling of high strength steel. Wear, 286–287, 116–123. https://doi.org/10.1016/j.wear.2011.05.007
- Brinksmeier, E., Meyer, D., Huesmann-Cordes, A. G., & Herrmann, C. (2015). Metalworking fluids: Mechanisms and performance. CIRP Annals, 64(2), 605–628. https://doi.org/10.1016/j.cirp.2015.05.003
- Canter, N. (2011, March). Monitoring metalworking fluids. Tribology & Lubrication Technology. https://www.stle.org/files/TLTArchives/2011/03_March/Cover_Story.aspx
- Debnath, S., Reddy, M. M., & Yi, Q. S. (2014). Environmental friendly cutting fluids and cooling techniques in machining: A review. Journal of Cleaner Production, 83, 33–47. https://doi.org/10.1016/j.jclepro.2014.07.071
- Diniz, A. E., Braghini Júnior, A., & Teixeira Filho, F. (2008). Tool wear damage caused by abundant emulsion in milling operation of PH stainless steel. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 30(2). https://doi.org/10.1590/S1678-58782008000200005
- Ezugwu, E. O. (2005). Key improvements in the machining of difficult-to-cut aerospace superalloys. International Journal of Machine Tools and Manufacture, 45(12–13), 1353–1367. https://doi.org/10.1016/j.ijmachtools.2005.02.003
- Ezugwu, E. O., & Bonney, J. (2004). Effect of high-pressure coolant supply when machining nickel-base, Inconel 718, alloy with coated carbide tools. Journal of Materials Processing Technology, 153–154, 1045–1050. https://doi.org/10.1016/j.jmatprotec.2004.04.329
- Health and Safety Executive [HSE]. (2021). MW5, Managing fluid quality: COSHH essentials for machining with metalworking fluids. https://www.hse.gov.uk/pubns/guidance/mw5.pdf
- Khan, T., Broderick, M., & Taylor, C. M. (2021). Investigating the industrial impact of hydraulic oil contamination on tool wear during machining and the development of a novel quantification methodology. The International Journal of Advanced Manufacturing Technology, 112(1–2), 589–600. https://doi.org/10.1007/s00170-020-06370-y
- Li, H., Zhang, Y., Li, C., Zhou, Z., Nie, X., Chen, Y., Cao, H., Liu, B., & Zhang, N. (2022). Extreme pressure and antiwear additives for lubricant: Academic insights and perspectives. The International Journal of Advanced Manufacturing Technology, 120(1–2). https://doi.org/10.1007/s00170-021-08614-x
- Liao, Z., Schoop, J. M., Saelzer, J., Bergmann, B., Priarone, P. C., Splettstößer, A., Bedekar, V. M., Zanger, F., & Kaynak, Y. (2024). Review of current best-practices in machinability evaluation and understanding for improving machining performance. CIRP Journal of Manufacturing Science and Technology, 50, 151–184. https://doi.org/10.1016/j.cirpj.2024.02.008
- National Institute for Occupational Safety and Health [NIOSH]. (1998). Criteria for a recommended standard: Occupational exposure to metalworking fluids (DHHS [NIOSH] Publication No. 98-102). https://www.cdc.gov/niosh/docs/98-102/
- Trent, E. M., & Wright, P. K. (2000). Metal cutting (4th ed.). Butterworth-Heinemann.
- Yan, P., Rong, Y., & Wang, G. (2016). The effect of cutting fluids applied in metal cutting process. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 230(1), 19–37. https://doi.org/10.1177/0954405415590993