BlogApplication notes
Why won't the rust preventive film come off in the next process?
- Type
- Application notes
- Published
- 20 November 2026
- Prepared by
- Technical team
- Product group
- Corrosion Prevention
When film survives into the next process, the usual move is to run the wash again, but the film is made to cling to metal and does not readily yield to the same conditions repeated. What actually leaves it behind can be a heavy or hard film, weak wash conditions, an oil-loaded bath, film aged by heat and time, or inhibitor bonded to the metal, and two of these can act together.
Some days, parts that arrived with rust preventive oil go through the usual degreasing and still come out with crater-like spots on the paint line, stained phosphate coatings or plating missing in patches. Running the wash again brings the same defect back in the same place.
When film remains, paint and plating sit on oil instead of metal, and the result shows up as lifting, crater-like defects, stains and bare spots in the plating. The standard guide on cleaning before electroplating notes that plating needs a higher level of cleanliness than most other finishes (ASTM International, 2025). Leftover film shows up as a defect only at the end of the line, so every part made in between becomes rework.
A rust preventive is a temporary film that stops rust for weeks to months between machining, heat treatment, storage and shipping. It usually goes on in one coat 2 to 20 micrometres thick, is most often stripped with an alkaline degreasing cleaner once its job is done, and the next process, such as painting, phosphating, plating or welding, works only if it comes off cleanly (McGuire, 2016). Yet the film is built to push water away and cling to metal. Polar ingredients such as sulfonates, whose molecules have an electrically lopsided end, bond chemically to the metal at one end while their long tails tangle with wax chains to keep water out (McGuire, 2016). A film that clings well also lets go poorly, so cleaning has to supply enough to break that bond.
In such cases the technical team sets up the five hypotheses below and rules them out one by one. The first move is the same every time: pour clean water over a cleaned part and note where and how the water film breaks (ASTM International, 2021), and on the same day measure the bath temperature and concentration and compare them with the maker's recommended range.
Hypothesis 1: heavy or hard film
Look at this hypothesis first when the preservative has been switched to a wax or hard-film type for longer storage, for dipped parts where the film pooled instead of draining, and for parts with many corners and threads. This is especially so when the degreasing line is still set for a thin oil and only the preservative has changed. Say export orders lengthen storage, so the preservative is switched to a wax type while the degreasing line stays as it was. At the lower edge of the cleaned parts and between the threads, a film remains that smears under a fingernail.
The first reason film stays is that preservatives leave different kinds of film. Oil-based products never dry and stay as an oily film, while solvent-cutback products leave a firmer film as the solvent evaporates (McGuire, 2016). The US defence specification divides solvent-cutback compounds into five grades, hard film, soft film, water-displacing soft film, transparent non-tacky film and film removable by low-pressure steam, and requires the hard film to start flowing only at 80 °C or above (DoD, 2017). The Japanese industrial standard likewise sorts rust preventive oils into solvent-cutback, petrolatum, a semi-solid jelly-like oil, and lubricating-oil types, among others, and has a separate test for film removability (JSA, 2026).
Wax is a strongly crystalline solid (McGuire, 2016). If the cleaner is colder than the point where the film melts or flows, the film stays solid and the cleaner only chips at its surface. The type of sulfonate matters too: in the same alkaline cleaning test, barium sulfonate films came off less completely than calcium sulfonate films (McGuire, 2016). Thickness plays its part as well. Rust preventive is usually applied 2 to 20 micrometres thick, but it pools much thicker where it has not drained after dipping, in corners and in threads, and since cleaner dissolves a film from the outside in, thick spots do not clear in the same time and stay behind.
Start by finding out what kind of film it is. Check whether the product or supplier changed when the film started staying, and find in the SDS and technical data sheet whether it is an oil type, a solvent cutback, a wax or a hard film. If it smears like oil under a finger, it is an oil type; if it scrapes like dry wax, it is a wax or hard film. Measure the bath temperature and compare it with the melting point or the flow point, the temperature at which the film starts to run, in the data sheet, and if film stays only at the lower edge of a part or in recesses, suspect thickness rather than type.
Weigh the next process's cleaning conditions from the moment the preservative is chosen. For short storage between processes, a thinner, softer grade may be enough. If a hard or wax film must stay, raise the cleaning temperature above the film's flow point, or add the removal method the supplier's data sheet names for that film, such as a solvent pre-clean or steam (DoD, 2017). If thickness is the cause, hang parts at an angle after dipping so they drain fully, and for spray application adjust the flow and distance so the film does not pool. When changing preservatives, run a few real parts through the next process's cleaning before rolling the change out to the whole line.
Hypothesis 2: weak wash conditions
If the film type has not changed but some days leave film and others do not, look at the wash conditions. Cases include a bath not yet up to heat on winter mornings or just after start-up, a tank topped up by feel without records, a line where immersion time was cut to keep up with output, a spray washer with blocked nozzles, and baskets with parts piled on one another. On one wash line, film stays only on the first loads on Monday, while that afternoon's batches come out clean. The washer takes its first basket as soon as it is switched on in the morning.
Alkaline degreasing is not one action but several working together. Fatty components react with the alkali to become water-soluble soaps, which is called saponification, and surfactants lower the surface tension between oil and water (Mihis et al., 2021). Mineral oil, which does not saponify, leaves by other routes. Surfactant works its way between the oil and the metal and rolls the oil up into droplets, breaks it into fine droplets carried in the water, which is emulsification, or dissolves it inside micelles, tiny clusters of surfactant molecules, which is solubilisation (Hubbe et al., 2022).
These actions lean heavily on conditions. In a carbon-steel degreasing study, raising the temperature thinned the oil and let the cleaner spread faster, which raised cleaning efficiency, and stronger stirring brought fresh solution to the surface and raised it further. Without agitation, the solution next to the surface fills with oil and cleaning slows sharply (Mihis et al., 2021). Ultrasonic cleaning works the surface with bubbles that form and collapse in the liquid, known as cavitation, though the details of how that cleans are still under study (Verhaagen & Fernández Rivas, 2016).
All four conditions can be measured. Read the bath temperature with a thermometer every shift and compare it with the set point; if film stays only when the bath is not yet hot, suspect temperature. For concentration, titrate for alkalinity or read a refractometer by the supplier's method and compare with the maker's recommended range. For time and agitation, check the actual immersion time, spray pressure and blocked nozzles, and if film stays only where parts overlap or inside holes, where the solution cannot reach, treat it as a problem of agitation and contact.
Change the conditions one at a time. If the temperature is low, bring it into the maker's recommended range first; if the concentration is low, track additions in a log; and re-rack or re-basket overlapping parts so the solution has a path to flow. For processes that need high cleanliness, such as plating, follow the standard guide's advice to keep multistage cleaning even for light soils (ASTM International, 2025). After each change, check the result with a water-break test, and log the new setting with the result so the next occurrence has a starting point (ASTM International, 2021).
Hypothesis 3: oil-loaded bath
Suspect this hypothesis on lines with a single tank, lines fed with heavily oiled parts, tanks topped up for a long time without a change, and equipment with nothing to remove floating oil. As the basket is lifted out of the bath, oil floating on the surface clings to the parts again on the way up. A ring of oil runs round the tank wall at the waterline.
Cleaning power drops because a bath can take on only so much oil. Surfactant used in emulsifying and solubilising stays bound up with the oil, and alkali used in saponification is consumed (Hubbe et al., 2022; Mihis et al., 2021). As oil builds up with every load, the bath has less room for new oil, and oil already removed can settle back on the parts.
Tests at a public cleaning laboratory put numbers on that change. Removal of oil from cold-rolled steel was 99.3% in fresh cleaner; in cleaner used for one month it was 97.8% for a standing bath and 98.6% for a circulating one, and in cleaner used for three months it fell to 92.3%. The same report noted that filtration and oil separation extend bath life (TURI, 1997).
The surface and the tank wall tell you first. Oil floating on the bath or a ring on the wall means oil is building up, and if parts come out clean for a few days after a fresh charge and then film creeps back, this hypothesis is the strong one. Logging change-out dates, additions and throughput together shows in advance when cleaning power will start to fall. A control test settles it: wash parts like the ones that kept film in fresh cleaner, and if they come clean only in the fresh solution, the bath is the cause.
Fitting equipment that removes oil is the starting point. Add a skimmer, an oil separator or filtration to take off floating oil, and set change-out intervals by throughput rather than by date (TURI, 1997). If there is only one tank, put a pre-clean stage in front to take most of the oil, so the main tank stays clean longer (ASTM International, 2025).
Hypothesis 4: aged film
This hypothesis comes up for lots stored a long time, parts kept in a summer warehouse, near a furnace or in sunlight, and parts oiled while still hot from machining or heat treatment. Picture a lot that spent the whole summer in a warehouse under the roof. Parts recently coated with the same preservative strip cleanly in the degreaser, but this lot comes out with a sticky brown film still on it.
The chemistry behind the hardening is oxidation. Oil that meets oxygen slowly oxidises into products such as acids, resins and sludge, and metals and water speed the reaction. As a rule of thumb the oxidation rate roughly doubles for every 10 °C rise, and the oxidation products are more polar than the original oil, so they dissolve poorly in it and stick to the polar metal surface (Hong & Jang, 2023).
Thin films change especially fast because so much of them touches the air. Fatty-alcohol films spread thin on steel and held at 90 °C formed oxidative polymers, and the unsaturated component, which has double bonds, turned into a gel-like solid over time (Bražinskienė et al., 2017). Mineral oil that touches hot metal also oxidises and leaves varnish-like deposits (Hong & Jang, 2023). These larger molecules dissolve in cleaner less readily than the original film, so they stay as a sticky brown layer under the same cleaning conditions.
Match each lot's storage history against the state of its film. See whether film stays only on lots stored long or parts kept somewhere hot, and whether a film that was clear has gone yellow or brown and turned tacky or varnish-hard. Putting freshly coated and long-stored parts with the same product through the same bath together separates an aged film from a cleaning problem.
The fix starts with using parts before the film hardens. Shorten storage, use parts first in, first out, and keep them somewhere cool and shaded. If long storage cannot be avoided, ask the supplier for a grade that resists oxidation and its recommended removal method. For film that has already hardened, run the pre-clean the supplier recommends, such as a solvent or hot clean, rather than repeating the normal wash.
Hypothesis 5: bonded inhibitor layer
Consider this hypothesis when the visible film has gone, yet the water film still breaks and the next process shows defects. It matters most on lines using preservatives rich in sulfonates and in processes sensitive to surface cleanliness, such as plating and bonding. The degreased parts look and feel free of oil. Pour water over them, though, and the water film splits into islands, and when such a part is plated, bare patches show here and there.
Inhibitors are put there precisely to stick to metal. The polar head of a sulfonate chemisorbs, bonding chemically to the metal, and other polar additives such as fatty acids also adsorb onto the surface (McGuire, 2016). Cleaning can strip the visible oil and still leave this single molecular layer, tails pointing outward, repelling water. The test in which barium sulfonate films came off less completely than calcium sulfonate films reflects this difference in bonding (McGuire, 2016).
The layer is too thin to see, yet thick enough to harm the next process. In a pre-plating test, panels where the preservative had not been fully removed showed gaps in the copper deposit (McGuire, 2016).
An invisible layer is found with water. The water-break test, pouring clean water over a cleaned part and seeing whether the water film stays unbroken, can detect even molecular layers of water-repelling contaminant, but it only separates pass from fail and loses sensitivity on rough or porous surfaces (ASTM International, 2021). When a number is needed, measure the contact angle of a water drop: below 45° the surface wets well with water, and above 90° it repels water (ASTM International, 2022). For steel parts, dip in copper sulfate solution and see whether copper deposits evenly, reading bare spots as places where film remains (McGuire, 2016).
When the water film breaks with no visible film, consider adding a step after cleaning that lifts the last surface layer. Examples are electrocleaning, passing current through the cleaner so gas bubbles at the surface lift the film, and acid activation, a short dip in dilute acid that exposes fresh metal; in pre-plating cleaning, a final electroclean serves to remove remaining impurities (ASTM International, 2025). When choosing a new preservative, ask the supplier for removability test results under the next process's conditions (JSA, 2026).
Testing the hypotheses
Most of the tools needed to sort out the five hypotheses are already on the floor: water, a thermometer, a titration kit and the records. The first step is a water-break test on cleaned parts, marking where film remains on a sketch of the part (ASTM International, 2021).
Where the film stays is the first fork. Film only on overlapping faces or inside holes leans towards agitation and racking, hypothesis 2; film gathered at the lower edge, in recesses or in threads leans towards thickness, hypothesis 1. If no film can be seen at all and the water film still breaks, suspect hypothesis 5 straight away.
Next comes the bath. If temperature or concentration is outside the maker's recommended range, correct hypothesis 2 first. If both are in range and film still stays, check for oil on the surface and the change-out history, and run the control test of washing the same parts in fresh cleaner. If they come clean only in fresh solution, it is hypothesis 3 (TURI, 1997).
If fresh cleaner does not clear it either, turn to the film. Checking whether the preservative or supplier changed, and what type of film it leaves, settles hypothesis 1, and comparing freshly coated and long-stored parts under the same conditions settles hypothesis 4. Confirm an invisible molecular layer with the contact angle or a copper deposit check (ASTM International, 2022; McGuire, 2016).
After a fix, the job is done only when the water-break test keeps passing across several baskets and the defects in the next process have gone.
The hypotheses can overlap. A wax film that hardens in a summer warehouse and then goes into an oil-loaded bath brings hypotheses 1, 3 and 4 into play at once. In that case fix the wash conditions first, since they are easiest to change, then treat what remains as a question of film type and storage. Change one thing at a time so the effect of each change is clear.
Limits and cautions
Cleaner concentration and temperature, and the removal method for a preservative, differ by product, so follow the supplier's data sheet and SDS. The water-break test gives only a pass or fail and says nothing about the amount or type of contaminant (ASTM International, 2021), so for demanding processes such as plating or bonding, bring in specialists who can analyse the surface.
Take care with safety as well. Sodium hydroxide, a common ingredient of alkaline cleaners, is corrosive and burns the eyes and skin, and the US NIOSH recommends an airborne exposure ceiling of 2 mg/m³ (NIOSH, n.d.). Use safety glasses, chemical-resistant gloves and local exhaust around hot cleaning tanks. Chlorinated solvents for dissolving films face tightening rules because of health risks: in 2024 the US Environmental Protection Agency issued a rule prohibiting trichloroethylene in vapour degreasing (EPA, 2024). Deadlines can change, so check the current local regulations before using any solvent.
Sources
- ASTM International. (2021). ASTM F22-21, Standard test method for hydrophobic surface films by the water-break test. https://store.astm.org/f0022-21.html
- ASTM International. (2022). ASTM D7334-08(2022), Standard practice for surface wettability of coatings, substrates and pigments by advancing contact angle measurement. https://store.astm.org/d7334-08r22.html
- ASTM International. (2025). ASTM B322-99(2025), Standard guide for cleaning metals prior to electroplating. https://store.astm.org/b0322-99r25.html
- Bražinskienė, D., Strakšys, A., Voišnienė, V., Vilkauskaitė, R., & Asadauskas, S. (2017). Oxidative decomposition of thin films of oleyl and stearyl alcohols on steel surface. Chemija, 28(1), 1–8. https://lmaleidykla.lt/ojs/index.php/chemija/article/download/5629/4815
- Hong, S.-H., & Jang, E. K. (2023). Varnish formation and removal in lubrication systems: A review. Materials, 16(10), 3737. https://doi.org/10.3390/ma16103737
- Hubbe, M. A., Szlek, D. B., & Vera, R. E. (2022). Detergency mechanisms and cellulosic surfaces: A review. BioResources, 17(4), 7167–7249. https://doi.org/10.15376/biores.17.4.Hubbe
- Japanese Standards Association [JSA]. (2026). JIS K 2246:2026, Rust preventive oils. https://webdesk.jsa.or.jp/preview/pre_jis_k_02246_000_000_2026_e_ed10_ch.pdf
- McGuire, N. (2016, September). Fundamentals of rust preventives used for temporary corrosion protection. Tribology & Lubrication Technology, 28–34. Summary of an STLE webinar by G. Moran and B. Faber. https://stle.org/images/pdf/STLE_ORG/BOK/LS/Metalworking/Fundamentals%20of%20RUST%20PREVENTIVES%20used%20for%20temporary%20corrosion%20protection.pdf
- Mihis, A., et al. (2021). The effect of alkali and surfactant concentration, temperature and stirring on the cleaning efficiency of the carbon steel surface. Studia UBB Physica, 66(1–2), 79–90. https://doi.org/10.24193/subbphys.2021.08
- National Institute for Occupational Safety and Health [NIOSH]. (n.d.). NIOSH pocket guide to chemical hazards: Sodium hydroxide. CDC. https://www.cdc.gov/niosh/npg/npgd0565.html
- Toxics Use Reduction Institute [TURI]. (1997). CleanerSolutions cleaning trial: Client 44, Project 1, Trial 4. University of Massachusetts Lowell. https://cleanersolutions.org/Browse-Client-Types/(client)/44/(project)/1/(trial)/4
- U.S. Department of Defense [DoD]. (2017). MIL-PRF-16173E, Corrosion preventive compound, solvent cutback, cold-application (Amendment 2). https://standards.globalspec.com/std/10187577/mil-prf-16173
- U.S. Environmental Protection Agency [EPA]. (2024, December 17). Trichloroethylene (TCE); Regulation under the Toxic Substances Control Act (TSCA). Federal Register, FR Doc. 2024-29274. https://govinfo.gov/content/pkg/FR-2024-12-17/pdf/2024-29274.pdf
- Verhaagen, B., & Fernández Rivas, D. (2016). Measuring cavitation and its cleaning effect. Ultrasonics Sonochemistry, 29, 619–628. https://doi.org/10.1016/j.ultsonch.2015.03.009