KALTEC

BlogApplication notes

Why is my rust preventive sticky and collecting dust?

Type
Application notes
Published
20 November 2026
Prepared by
Technical team
Product group
Corrosion Prevention

A sticky, dusty rust preventive film is easy to blame on a bad batch, but tack can be a built-in property of the film or come from how it was applied, dried and stored. What actually makes the film sticky can be a film that is soft by design, excess coating, packing too soon, heat in storage or film oxidation, and two or three of these can act on the same part.

Sometimes a box of parts ready to ship opens and the coated surfaces feel tacky, with grey dust and lint packed onto the film. There is no rust in sight, yet the receiving end calls the parts dirty and gloves on the assembly line turn black in no time. Often the complaint comes with a twist: the product has not changed, but only one line or one season has the problem.

Tack alone does not mean rust, but it costs the process. Sticky parts need an extra degreasing step before assembly, and dust or chips that reach precision fits, paint or bond surfaces become defects. The customer's first impression suffers as well. A film that comes off on the hands is an old problem: the US Navy ran a separate evaluation of dry-to-the-touch, ultra-thin film compounds (Naval Air Development Center, 1971).

A rust preventive is a temporary film that keeps parts from rusting for weeks to months between machining and assembly or shipment. By base it is solvent-based, oil-based or water-based, and the active part is a corrosion inhibitor, such as a sulfonate, amine or amide, that adsorbs on the metal (Tang, 2019). Films divide into hard or dry-film types that are dry to the touch once set, and soft types that stay soft and close up again when scratched (DoD, 1993; NPL, n.d.). Whether tack is a defect or a property can only be judged once you know which kind of film was chosen.

Faced with this, the technical team sets up the five hypotheses below and rules them out one at a time. The first check never changes: read the film type, recommended thickness, drying time and service temperature on the product's technical data sheet, the TDS, and write the actual coating amount, drying time and storage temperature next to them.

Hypothesis 1: soft film by design

Start with this hypothesis when the TDS uses words such as soft film, oil film or self-healing, or gives no drying time at all. It shows up when an oil-type or soft-wax product made for short indoor storage ends up somewhere it was not meant for, such as long-term storage, beside a grinding line or in a dusty warehouse. Shafts coated with an oil-type preventive and stacked for a few weeks on a shelf next to a grinder are a good example. Oil comes off on a finger from the first day and does not improve with time, and grinding swarf has settled evenly over the top faces.

Rust preventive specifications grade film hardness from the outset. US military specification MIL-PRF-16173 covers compounds that leave a thin film once the solvent evaporates, divides them into grades such as hard film, soft film and water-displacing soft film, and requires some grades to stay soft after drying and exposure (DoD, 1993). A soft film heals itself when scratched because oil flows back over the gap, but that also means its surface stays close to liquid (NPL, n.d.).

This is also where the grip on dust comes from. When a dust particle lands on such a surface, oil forms a small bridge between the particle and the film, known as a liquid bridge. The capillary force with which that bridge pulls on the particle can be far larger than the weak intermolecular attraction, the van der Waals force, that holds particles on a dry surface (Bowling, 1988). So a soft film keeps gathering airborne dust, grinding swarf and fibres. The US Navy evaluated dry-to-the-touch compounds precisely because existing products left films that were not dry to the touch (Naval Air Development Center, 1971).

A TDS and a fingertip are enough to decide. If the TDS states a soft-film type and the tack has been there unchanged since coating, the tack is better read as a property of the film than as a defect. Note the product's intended use beside where it is actually used, along with storage time and indoor or outdoor exposure, and the mismatch shows itself.

When tack is a property, the thing to fix is the product choice. Write down the storage time, indoor or outdoor exposure and whether the next step degreases the parts, then choose the film type again. If parts must be dry to the touch, move to a dry-film or hard-wax type; if scratch protection matters more, keep the soft film and keep dust off with packaging (NPL, n.d.). Before switching, test that the new film comes off with the downstream cleaning method.

Hypothesis 2: excess coating

Coating amount drifts easily from line to line, shift to shift and day to day. Films grow thick when dipped parts are not drained enough, when spray output is high and when the dip tank is kept too concentrated, and then the same product turns out stickier on some lines or shifts than on others. Take a line where brackets come out of the dip tank and go straight onto a rack, upright and undrained. Fluid beads up along the lower edges and around the holes, and only those spots are especially sticky, with dust built up thickly on them.

A thick film turns into tack by one of two routes, depending on the product. A solvent-based preventive carries its solids, such as wax, oil and inhibitors, in a solvent, and the film forms as the solvent evaporates (DoD, 1993). Solvent leaves from the surface, so the thicker the film, the longer it takes solvent deep inside to get out; the surface can set first and look dry while the inside stays soft for a long time. Film drying runs through stages such as set-to-touch, tack-free and dry-hard, and the standard test judges each stage separately (ASTM International, 2022).

Thickness matters for oil-type products as well, even without solvent. A thick film leaves more free oil on the surface, so liquid bridges form around dust more easily (Bowling, 1988), and on parts standing upright the oil runs down and pools, making those spots especially sticky.

Measuring settles it. Read wet film thickness with a comb gauge and dry film thickness with a thickness gauge (ISO, 2019). Weighing a reference coupon before and after coating gives the coating weight per area just as simply. Measure the same way on each line and shift and set the readings against the TDS value, and it is plain whether the tack sits with the thicker films.

If readings run above the recommended thickness or coating weight, lengthen the drain time after dipping or cut the spray output. For products used diluted, check the bath's density or viscosity regularly along with the dilution ratio, because the bath thickens as solvent evaporates. Once the target is set, check coating weight on a reference coupon every shift so the film does not creep back up.

Hypothesis 3: packing too soon

Drying trouble follows the season and the hour. It is likely when the coating area is cold or the air is still, when parts are dried packed tightly together, and when a shipping deadline means parts are wrapped as soon as they are coated, so complaints rise in winter, on rainy days and on night shifts. On a cold morning, parts sprayed with a solvent-based preventive go straight into plastic film and a box. A few days later the box opens to a rush of solvent smell, touching parts are stuck together and film has transferred to the inside of the plastic.

A solvent-based preventive becomes a proper film only when its solvent leaves into the air (DoD, 1993). The evaporation rate depends on temperature, air movement and how much solvent vapour the surrounding air already holds, and low temperature, still air or tightly stacked parts keep the vapour from escaping and slow drying. Standard drying tests fix temperature and humidity because drying time changes a great deal with these conditions (ASTM International, 2022). Wrap or box parts before they dry and the air inside soon fills with solvent vapour, evaporation all but stops, and the trapped solvent keeps the film soft for a long time. That is why even a dry-film product behaves like a soft film when its drying time is cut short.

A fingertip tells the stages apart. Press lightly and see whether film transfers and whether tack remains, and the drying stages can be judged one by one (ASTM International, 2022). Check parts this way just before packing, and log the coating-area temperature and the time from coating to packing. A strong solvent smell on opening, or film transferred to the packaging, adds weight to this hypothesis.

Let the film, not the clock, decide when to pack. Check the drying time on the TDS and the temperature it assumes, and allow longer when the shop is colder. In the drying area, space the parts so air can flow, and pack only after the tack-free stage is confirmed. Solvent vapour is a health and fire hazard, so ventilation serves safety as well as drying speed (NIOSH, n.d.).

Hypothesis 4: heat in storage

Heat in storage turns a film that was fine at coating sticky after the fact. That is the case when tack appears only in summer, after sea freight, on top racks or near windows, and coating parts still warm from heat treatment or washing belongs here too. Parts coated with a wax-type preventive and put on the top shelf by a sunny window in midsummer show the pattern: touched in the afternoon the film comes off tacky, and by the cool of the morning it has firmed up again, but with dust set into the surface.

Oil and wax respond to heat in slightly different ways. The viscosity of petroleum oils falls quickly as temperature rises, a relationship set out in standard viscosity-temperature charts (ASTM International, 2020). An oil film that sits well at room temperature thins and runs in a midsummer warehouse or a container in the sun, leaving a wetter, stickier surface. A wax film is close to solid below a certain temperature but softens as it nears its melting range. High-viscosity waxes such as petrolatum, also known as petroleum jelly, and microcrystalline wax are compared by drop melting point, the temperature at which the first drop falls on heating, and the value can differ by test method (ASTM International, 2025). As storage temperature nears that value, even a hard wax film turns tacky and then sets again with dust embedded.

Temperature records are the evidence. Put a temperature logger in the storage area and compare the peak it records with the TDS service range or the wax's drop melting point (ASTM International, 2025). Moving a sticky part somewhere cool and seeing whether the film firms up is another easy check. If it firms up, heat is the likely cause; if it stays sticky, look at the other hypotheses too.

There are two ways out: change the product or change the place. If peak storage temperature exceeds the product's range, move to a wax type with a higher melting range or to a dry-film type. Let parts cool to room temperature after heat treatment or washing before coating them, and for container shipments choose a stowage position out of direct sun. Hold any candidate product at the measured peak temperature for at least a day and check tack and flow before bringing it in.

Hypothesis 5: film oxidation

Turn to this hypothesis last when a film that was fine at first has yellowed and turned sticky after some months. The change is likely on parts stored for months, in product left open long after the drum was opened, and in a dip tank reused for a long time without a change. Consider a tank that has been run on top-ups alone for months: the fluid is darker than fresh product and smells different, and parts dipped in it still show stains after the usual degreaser.

The sticky layer is what a slow reaction with oxygen leaves behind. Components with double bonds, that is, unsaturation, such as vegetable oils, react slowly with oxygen in the air. This autoxidation runs through initiation, where radicals, highly reactive molecules with an unpaired electron, form; propagation, where they take up oxygen and spread; and termination, where molecules join, ending in a crosslinked network (Honzíček, 2019; Soucek et al., 2012). In paint this is what cures the film; in a rust preventive film it tends to leave a half-cured, sticky layer.

Mineral oils are no exception. With long exposure to heat and oxygen they oxidise into acids, resins and sludge, which differ chemically from the oil, barely dissolve in it and remain as sticky or hard deposits known as varnish. Heat, light and metal surfaces speed this oxidation up (Hong & Jang, 2023).

Setting the tank fluid beside fresh product is the simplest check. Coat one coupon with each, compare colour and tack, and try removing both with the same degreaser. If only the tank fluid is darker, stickier and harder to remove, oxidation is the likely cause. Note the parts' storage time, the date the drum was opened and the date the tank was last changed as well.

The key to oxidation is managing time. If storage outlasts the period the product was designed for, switch to a long-term product or set an interval for recoating. Set a change-out interval for dip tanks, and close drums right after use and keep them cool. If a bio-based product is in use, ask the supplier for oxidation stability data.

Testing the hypotheses

Sorting out the five hypotheses takes no special equipment; strike them off in order, starting with whatever is easiest to measure. The starting point is the TDS comparison from the opening. If the film is a soft type and the tack has been unchanged since coating day, hypothesis 1 nearly settles it, and what remains is to choose the product again (DoD, 1993; NPL, n.d.).

The next clue is when the tack appeared. Tack from the moment of coating points to film type, thickness or drying, hypotheses 1 to 3; tack that developed in storage points to heat or oxidation, hypotheses 4 and 5. That one question splits the five into two groups.

For the first group, move to measurement. Measuring coating weight or film thickness on a reference coupon against the recommended value sorts out hypothesis 2 (ISO, 2019), and judging by fingertip whether parts reached the tack-free stage before packing sorts out hypothesis 3 (ASTM International, 2022). For the second group, log the peak storage temperature and compare it with the service range or drop melting point (ASTM International, 2020, 2025), and see whether a part moved somewhere cool firms up again.

Any doubt that remains goes to control coupons. Coat fresh product and in-use fluid on coupons under the same conditions and set them side by side; if only the tank fluid darkens and turns sticky, hypothesis 5 shows itself (Hong & Jang, 2023). When changing thickness or drying time, likewise keep a changed coupon beside an unchanged one, which gives the final check on whether the change really worked.

The hypotheses often overlap. A thickly applied soft film left in a summer warehouse brings hypotheses 1, 2 and 4 into play together. In that case change one thing at a time and compare on coupons, starting with the change likely to matter most, such as film type.

Limits and cautions

A product's protective performance or compliance with a specification cannot be judged from floor observation alone. Where compliance matters, have the specified tests run by an accredited laboratory. If rust is already forming under the film, or tack comes with widespread discolouration or staining, the protection itself needs to be re-evaluated. A change of film type can affect downstream degreasing, painting and bonding, so trial it with the process owner before adopting it.

Solvent-based rust preventives and degreasing solvents carry fire and inhalation hazards. Before work, read the product's safety data sheet, the SDS, provide ventilation and keep ignition sources away, wear protective gloves and safety glasses, and use organic-vapour respiratory protection where needed (NIOSH, n.d.).

Sources

  1. ASTM International. (2020). ASTM D341-20, Standard practice for viscosity-temperature equations and charts for liquid petroleum or hydrocarbon products. Reapproved 2025. https://store.astm.org/d0341-20r25.html
  2. ASTM International. (2022). ASTM D1640/D1640M-14(2022), Standard test methods for drying, curing, or film formation of organic coatings. https://store.astm.org/d1640_d1640m-14r22.html
  3. ASTM International. (2025). ASTM D127-25, Standard test method for drop melting point of petroleum wax, including petrolatum. https://store.astm.org/d0127-25.html
  4. Bowling, R. A. (1988). A theoretical review of particle adhesion. In K. L. Mittal (Ed.), Particles on surfaces 1. Plenum Press. https://doi.org/10.1007/978-1-4615-9531-1_10
  5. Hong, S.-H., & Jang, E. K. (2023). Varnish formation and removal in lubrication systems: A review. Materials, 16(10), 3737. https://doi.org/10.3390/ma16103737
  6. Honzíček, J. (2019). Curing of air-drying paints: A critical review. Industrial & Engineering Chemistry Research, 58(28), 12485–12505. https://doi.org/10.1021/acs.iecr.9b02567
  7. International Organization for Standardization [ISO]. (2019). ISO 2808:2019, Paints and varnishes — Determination of film thickness. https://www.iso.org/standard/71583.html
  8. National Institute for Occupational Safety and Health [NIOSH]. (n.d.). NIOSH pocket guide to chemical hazards: Stoddard solvent. Centers for Disease Control and Prevention. https://www.cdc.gov/niosh/npg/npgd0569.html
  9. National Physical Laboratory [NPL]. (n.d.). Temporary corrosion protection. Guides to Good Practice in Corrosion Control No. 7. https://www.npl.co.uk/electrochemistry/corrosion-guides
  10. Naval Air Development Center. (1971). Evaluation of dry-to-the-touch, ultra thin film, water displacing corrosion preventive compounds. Defense Technical Information Center, AD0728779. https://apps.dtic.mil/sti/pdfs/AD0728779.pdf
  11. Soucek, M. D., Khattab, T., & Wu, J. (2012). Review of autoxidation and driers. Progress in Organic Coatings, 73(4), 435–454. https://doi.org/10.1016/j.porgcoat.2011.08.021
  12. Tang, Z. (2019). A review of corrosion inhibitors for rust preventative fluids. Current Opinion in Solid State & Materials Science. https://doi.org/10.1016/j.cossms.2019.06.003
  13. U.S. Department of Defense [DoD]. (1993). MIL-PRF-16173E, Corrosion preventive compound, solvent cutback, cold-application. Amendment 2, 2017. https://standards.globalspec.com/std/652399/mil-prf-16173

Product and site consultation

Leave your company, site and the product groups in use. Our engineer will get in touch to go through your site conditions and concerns. Materials, equipment, operating conditions and downstream steps show what should change and what can stay. If nothing needs to change, we will say so.

Contact us
After you contact us
  1. 01
    Site setup

    We confirm process conditions and needs first.

  2. 02
    Spec design

    We set the product spec and selection criteria.

  3. 03
    Comparison

    We compare matching candidates and propose.

  4. 04
    Tailored supply

    We supply on time and manage the stock.

  5. 05
    Site check

    We visit, check conditions of use and record.

  6. 06
    Use management

    We track use and change cycles to catch issues.

  7. 07
    Regular analysis

    We analyze the records and send a yearly report.