KALTEC

From cutting parts to 24 months of stockpiling at sea

K-defense exports complete Korean weapon systems and components to allied nations.

Defense

What is the defense industry?

The defense industry makes equipment for national defense, such as firearms, ammunition, armored vehicles and guided weapons, and the parts that go into them. This equipment is deployed in very different environments, from desert heat to arctic cold to coastal salt, and must stay ready for immediate use for long periods after deployment. Because steel, aluminum and Inconel are machined and sheet is pressed into shape, the work calls for cutting and forming lubrication, cleaning, chemical protective films and long-term corrosion protection suited to each material.

Even after completion, defense parts spend long periods in warehouses and containers through storage, sea transport and stockpiling abroad. Corrosion or surface damage in this period degrades equipment performance and can cause problems at the buyer country's acceptance inspection. So alongside machining precision, the industry needs care that protects surface condition until delivery and a system that documents the process. Defense does not end with delivering products that meet specification; it calls for technical cooperation that looks at process conditions and storage environment together.

  1. 01

    Metal cutting

    Steel, aluminum, Inconel and other materials are turned, milled and drilled into part shapes. If cutting heat cannot escape, the cut surface roughens or heat distortion remains. Choose a cutting fluid by tool life, surface quality and fluid type restrictions.

  2. 02

    Press and forming metal work

    Sheet for ammunition cases, armor plate and similar parts is shaped by pressing, roll forming and drawing. Where loads concentrate, a broken oil film causes scratches and cracks. Choose forming oil by lubricity, release and cleaning burden.

  3. 03

    Cleaning and degreasing

    Machining oil, forming oil, chips and oxide are removed from parts to expose a clean surface. Even a little leftover oil is where corrosion starts first. Choose cleaners by cleaning power, material compatibility and oil separation.

  4. 04

    Passivation pretreatment

    Aluminum part surfaces are stripped of oxide and activated for coating adhesion. 2000 and 7000 series differ in etch rate and smut formation, so one condition set leaves stains and poor adhesion. Choose pretreatment chemicals by etching power and immersion time per alloy.

  5. 05

    Phosphate and chromate-replacement conversion coating

    A chemical protective film, from zinc phosphate to chrome-free thin films, is formed on part surfaces. If the free-to-total acid ratio or accelerator concentration in a phosphate bath drifts out of range, the film peels or leaves pinholes. Choose chemicals by thickness, adhesion and bath maintenance.

  6. 06

    Anodizing and sealing

    An anodic oxide film is built on aluminum parts and its pores are sealed to raise corrosion resistance. Short seal time or low temperature leaves pores open, leading to early corrosion at sea. Choose chemicals by film uniformity and seal quality.

  7. 07

    Assembly and quality inspection

    Cleaned parts are assembled into modules and checked for dimensions, performance, insulation and durability. With earlier films removed, any gap lets moisture in and corrosion returns. Choose assembly grease and fixing agents by fastening and operation.

  8. 08

    Packing and primary VCI rust protection

    Parts are sealed individually or as modules in VCI film, paper and emitters for long-term protection. Too little inhibitor for the package volume lets corrosion appear over time. Choose packaging by protection period, tightness and part shape.

  9. 09

    Storage and stockpiling

    Finished parts and modules are stockpiled long term in indoor and outdoor warehouses. As emitter inhibitor is used up, protection weakens. Choose rust preventives by protection period, recharge intervals and resealing.

  10. 10

    Sea transport

    Goods are loaded into containers and on pallets and delivered to the buyer country over long voyages. Combined salt, humidity and temperature change speeds corrosion. Choose the protection setup by voyage length, climate at transit ports and acceptance inspection standards.

Regulation and certification

FAQ

Can higher-viscosity forming oil stop scratches in ammunition case drawing?

Raising viscosity sometimes helps, but the problem often comes back. Drawing scratches can come from the oil film failing under load or from material transferring onto the die surface, and the two call for different fixes.

Looking at scratch direction and die condition shows where to act. Long scratches in the drawing direction with material galled onto the die point to extreme-pressure performance and release; scratches concentrated in one area point to oil amount and application position. It is good to account in advance for the extra cleaning burden that higher viscosity brings.

Can products that are not on the defense qualified products list not be used at all?

For items where a specification applies directly, such as surface treatment, coatings and packaging rust preventives, using listed products is close to the rule. Not every stage is bound equally, though; for chemicals that do not stay on the part, such as cutting and cleaning fluids, the customer sometimes has room to decide.

Listing applies per product, so a different formulation from the same company needs its own listing, and changing a formulation after listing restarts the approval process. That is why defense suppliers often keep an existing listed formulation rather than move to a new one that performs slightly better.

Rust shows after about six months in VCI film. Should we use thicker film?

The cause is more often the amount of inhibitor and the seal than film thickness. VCI works by filling the space inside the package, so if inhibitor is short for the internal volume or the seal leaks, thicker film alone rarely changes the result much.

Reducing empty space inside the package can work better than adding inhibitor. Filling volume with foam inserts keeps the internal concentration up with the same amount and reduces film being crushed or torn in stacking. Inserts that touch the part surface can leave marks, though, so it is best to decide the contact material and shape together.

Can chemicals we use domestically be shipped as-is with export goods?

Some ingredients may be restricted at export, so it is good to check in advance. International export control lists and the importing country's entry standards apply separately, so it is safer to check both.

Export control looks not only at ingredients but also at end user and end use, so the same product can get a different answer when the destination country changes. For items going to several countries, sorting this out once per country is safer, and doing it at the same time as receiving acceptance inspection standards keeps the schedule from slipping.