From substrate cleaning to contact lubrication
The display industry manufactures the screens of consumer devices such as smartphones, tablets, TVs and laptops.

What is the electronics and display industry?
The electronics and display industry makes the screen panels and electronic modules that go into smartphones, TVs and vehicle instrument clusters. Thin film transistors and emissive layers are stacked very thinly on glass or polyimide substrates, so even a small organic mark left on the surface shows up as a defect on the screen. Because substrates, metal thin films, organic materials and circuit boards are handled together, requirements change with every layer: precision cleaning, residue removal, encapsulation and bonding, contact protection and equipment lubrication.
The risks in this industry are moisture, oxygen and fine contamination escaping from equipment. Organic emissive layers lose their emission properties on contact with moisture, and volatile components from equipment lubrication lower deposited film quality batch by batch. So purity, particles, volatile components and the long-term reliability of coating and bonding materials must be weighed alongside performance data. In electronics and displays, a decision to change one material is made over several years, so the validation schedule should be planned from the start.
- LCD yield loss from poor cleaning8-20%
- 01
Substrate cleaning
Particles, organics and metal ions are removed from glass or polyimide substrates to prepare the base for patterning. Fine particles left behind unsettle yield in all later steps. Choose cleaners by cleaning power, substrate fit and recontamination.
- 02
Photoresist coating, exposure and development
Photoresist is applied to the substrate, exposed and developed to form circuit patterns. Resist thickness variation causes broken patterns or uneven development. Choose chemicals by resolution, electronic-grade purity and stability in storage.
- 03
Etching and resist stripping
Etchant removes unwanted thin films, then stripper removes remaining resist. Unstable selectivity causes undercut, and incomplete stripping leaves residual film. Choose chemicals by removal power, selectivity and bath life.
- 04
Thin film deposition for TFT formation
Oxide, metal and semiconductor layers are deposited in sequence to form thin film transistors. Particles in the chamber unsettle device characteristics for that batch. Choose chamber cleaners and maintenance fluids by cleaning power and the effect of residue on the next film.
- 05
OLED organic emissive layer deposition
Fine metal masks are used in a vacuum chamber to deposit emissive, hole and electron layers at the molecular level. Organics on masks mean scrapping a whole batch. Choose cleaners by removal power, residue-free performance and mask material compatibility.
- 06
Moisture-barrier thin film encapsulation (TFE)
Inorganic and organic films are stacked alternately to protect organic layers from moisture and oxygen. One pinhole of moisture breaks down emission there. Choose encapsulants by barrier performance and outgassing data.
- 07
Driver IC packaging
Display driver ICs are packaged by die attach, wire bonding, molding and underfill, then attached to the panel. Voids left in underfill are where cracks start. Choose bonding materials by bond strength, flow and cure conditions.
- 08
Conformal coating and thermal management
A protective coating is applied over module boards and component surfaces, and thermal materials are applied to hot spots. Bubbles or cracks in the coating lower both insulation and heat dissipation. Choose materials by thermal conductivity, insulation resistance and flame rating.
- 09
Connector and FPC contact assembly
Flexible circuit boards, connectors and frames are attached to the panel and contacts are lubricated. Fretting and oxidation raise contact resistance slowly. Choose contact protectants by lubrication, oxidation control and plating fit.
- 10
Equipment cleaning and precision lubrication
Deposition and etch chambers, transfer robots and vacuum systems are cleaned regularly, and bearings and linear guides are lubricated. Volatiles that contaminate chambers unsettle line yield. Choose lubricants by service life, load conditions and outgassing data.
- 11
Final inspection and packing
Optical, electrical and reliability performance is checked, then panels are packed and shipped. In transfer and packing, reflective films can be damaged or devices harmed by static. Choose packaging materials by cushioning and antistatic grade.
Regulation and certification
SEMI standards
SEMI also publishes standards for flat panel display equipment and materials. Panel process chemicals and equipment consumables are chosen against the purity and contamination criteria these standards set.
ISO 14644
The international standard for cleanroom cleanliness classes and their control. Lubricants for panel-line transfer equipment and cleaners must be chosen for low particle shedding and low outgassing.
RoHS
The EU directive restricting hazardous substances such as lead, mercury and cadmium in electrical and electronic equipment. Adhesives, coatings and sealants that remain in display modules must also be checked for restricted substances.
Chemicals Control Act (Korea)
Korean law on the handling, facilities and accident preparedness for hazardous chemicals. Panel etchants and strippers classed as hazardous are stored and handled according to its requirements.
FAQ
After cleaning, stains remain only near the substrate edges. Why?
On large substrates, dwell time and rinse conditions often differ by position. At the edges, solution drains first and dries faster, so residue can remain as marks.
The point to check is whether the stain always appears in the same place. If it repeats in the same place, look first at nozzle layout or transfer angle; if the location changes each time, look first at cleaning solution condition and rinse water quality.
Residual film remains after stripping. Will a stronger stripper fix it?
Sometimes, but damage to underlying layers can increase as well. If residual film stays only in certain areas, uneven temperature or flow is a more likely cause than the strength of the solution.
Raising stripping power brings in underlying layer damage and bath life, so even when residual film decreases, waste burden and change frequency can increase. If residual film always remains in the same place, the problem likely starts with flow and temperature distribution rather than the chemical, and in that case it often repeats in the same place even with a different solution.
How does electronic-grade purity really differ from general industrial grade?
The items managed and the units differ. Analyzing metal ions and particles to much lower levels and keeping a certificate for every lot is where it departs from industrial grade.
Even with the same grade label, different measurement items and detection limits change what the values mean, and using industrial-grade data as is leaves no basis to trace back when spread appears on the line. Higher purity grades also raise unit price and lead time, so some set the required grade separately for each stage.
Does a material change always get side-by-side evaluation with the current one?
Often, yes. Panel materials directly affect device characteristics and lifetime, so short tests are not enough to judge, and comparing with the current material on the same line is the usual approach.
If line conditions change during evaluation, earlier results become hard to reuse and the evaluation sometimes starts over. Panel materials are often tied to exclusive supply arrangements, so even after passing parallel evaluation, volume does not move over at once but grows in steps starting from some lines.